COQ2BP Sii
5 t !5 t r !9 !8 @2 w !4 !2 !0 !0 !6 !6 i u !7 o i u !7 o !3 y !1 e q !3 y !1 q @7 CXSJM20 to 32 CXSJL20 to 32 @5 i u !7 o !5 t !6 r !9 !8 @2 r !9 !8 @2 !6 o i u !7 !5 t #0 Rod cover Head cover Rod cover Head cover Parts List: Standard Piping No. Description Material No.
B DIN rail mounting bracket [-D] VVQ1000-57A for {F, L, M, P, S (EX500) kit} VVQC1000-57A-S for {S (EX250) kit} VVQC1000-57A-T for {T, S (EX126) kit} 17 SOL. A 5 Station 7 SOL. B 18 SOL. A 6 Station 8 SOL.
POM Stainless steel Material Note y Description q Description Plunger Spring Valve Body T.T. = 2.5 mm only, w/threads w e u i Stainless steel Lever Packing O-ring NBR Valve Retainer Spring r POM o NBR t Stainless steel !
For actuators with external stopper, the rotation end can be set within the ranges shown in the drawing by adjusting the stopper bolt. c l o r e c t k n w u o i s C e CRB2 CRBU2 CRB1 MSU B port A port C e l o s c i w k CRJ Basic type For 90 and 100 For 180 and 190 CRA1 Single flat Single flat CRQ2 MSQ MRQ D+10 0 B port A port B port A port +8 0 00 20t 1 0 t 9 fla la gle e f gl sin sin of
VCC 0.4 0.3 TQ 0.2 0.1 0 1 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 Operating pressure (MPa) 619 A VNC Series Construction N.C. i i o o t t r w r w Port 12(P1) Port 10(P2) u u In the case of 32A to 50A y y N.C.
ad an an ju t r t r st en m en en stm m t r st ju ju an ad ad ge le e Ang 5 gl n A B port A port B port A port 90 A 5 n gl ge e an ad t r ju en st m 180 Note) The drawings show the rotation range for the shaft's single flat.
Actuator driving system Inside of clean room w t e q r t q Cylinder relief port piping w Solenoid valve exhaust piping e Breathing piping of regulator r Drain piping t Exhaust Cleaner for Clean room/AMP series Cylinder relief port piping Series 10-/12-/21(atmospheric release type) Connect the relief port piping with the dedicated duct piping installed outside the clean room or with the exhaust
2 w !2 w !3 !4 !5 With reducer Tube extensions e t y r i u q o !1 !0 !2 w Component parts No.
g n k n k ra c oc ra o t cl cl en nt er er e tm m nt nt e is 0 u us t 0 u C w us o o k lo c o C dj C l 19 C 19 dj se c Cl A k A A wi w oc e e dj A ck is ng ng k dj o u wi e Cl st us se ro ra ra m ta ro t m ta ti d e ti n o on e n n e n nt nt en tio tio d ra ra 5 n n g ta e ta 9 g e 5 9 ro ro m m u u im im ax M ax M Note) The drawing shows the rotation range of the positioning pin hole.
Unit/Specifications Air filter (w/auto-drain, w/manual drain) 5m Filtration Regulator 0.05 to 0.85MPa Set press.
0 i r t !2 !4 y e q !3 o w u !1 M: Rod end male thread 32 to 63 With auto switch (Built-in magnet) !0 !2 r t !4 y i e q !3 o w u 80, 100 With auto switch (Built-in magnet) !0 q w e r t y u i !2 !4 !3 Component Parts Replacement Parts/Seal Kit No. Description Material Note Cylinder tube Piston Bore size (mm) Kit no.
Stop 1)CC-Link cable (LECSC, LECSC-T), SSCNETIII cable (LECSS, LECSS-T) 2)When using test operation mode (JOG operation), the LECSC, LECSS, LECSC-T, LECSS-T need the MR-Configurator2TM. 6 - 1.3 Gain tuning 1.3.1 Procedure Here are the steps for basic gain tuning. Refer to the Driver operation manual for details and for tuning methods other than shown below.
Knuckle Pin (Common with double clevis pin) Rod End Nut d d Dd9 C m m l L t t H B Material: Carbon steel Material: Rolled steel (mm) (mm) Applicable bore size (mm) Applicable retaining ring Part no. Applicable bore size (mm) Part no.
Work W Work W Work W Work W Bracket Cylinder goes up Cylinder goes down Lever basic position Lever locked Lock released With cancel cap With lever detection switch RSQ When the lever stands erect (when the energy is absorbed), the switch turns on a signal that determines the pallet has reached the stop position. (For details of lever detection switch, refer to page 595.)
NPN + Analogue output type PF3W7--C(T)PF3W7--D(T)NPN + External input type PF3W7--G PNP 2 output type PF3W7--B(T)PNP + Analogue output type PF3W7--E(T)PF3W7--F(T)PNP + External input type PF3W7--HWhen accumulated pulse output is selected, the indicator light is turned off.
The tightening torque should be 0.1 to 0.2 Nm. 5 to 6 14 e-Rodless Actuator Series E-MY2 Names and Functions of Individual Part Controller detail w t q u End Motor I/O cable Controller Power supply cable Slider i y e r Switch FG terminal Motor side end Description Content/Function q w e r t y u i Stroke learning switch Description Content/Function Switch to move the actuator to intermediate
N.O. 1 (P) 3 (R) 1 (P) 3 (R) q e t r q e t r SY SYJ VK A A VZ u u VT VT P R P R VP w w VG y y VP Component Parts Replacement Parts VQ Description Body Piston plate End cover Piston Spool valve ass'y Description Sub-plate Pilot valve Note White White White Note Zinc die cast Parts No.
available in the case of D, DO, W type.