EXxx-OMK0006 Output numbers are assigned to side A and B alternatively. In case of single solenoid valve, output on side B is free. (Refer to fig.a) : Mixed (single and double) wiring is available as long as wiring specifications designate it. This allows output numbers to be specified without having free output.
(B)). Fig. (A) When air is supplied to the exhausted cylinder, the air causes the check valve to close. Also, because the piston valve is fully closed due to the cylinder's low internal pressure, air is supplied gradually via the throttle of the set needle. Therefore, the cylinder operates slowly under meter-in control. Fig. (B) Fig.
D E L 4-H Valve mounting hole F Bracket Mounting Dimensions/Bracket Material: Stainless Steel (mm) A B C D E F G H J L Valve model Bracket part no.
bracket) are included with the above parts. 3 Direct Operated 2 Port for Heated Water Series VCB Dimensions Grommet: G Conduit: C Q Approx. 300 F D Approx. 280 D Q F C G1/2 C R R E E B A H 2-P Port size 2-P A 2-M Thread depth N B H Port size 2-M Thread depth N L L K K Conduit terminal: T F (Q) 34 25 U R C G1/2 E B A H D 2-P Port size (S) 2-M Thread depth N L K (mm) Electrical entry P Port
These grcoves can b used for fnmly fixing the tying ba.ds or lad wis oi the auto switch, etc., dd also termiml boards, etc-, to the main body of the cylinder q " l-f9 -l lF'rg _1+T l---' l I I Detailed drawing ol part a Detailed drawing of part b Part a Patl a Ff"frf?
Disconnect the jumper wire from the remote terminal B (terminal number 6-7) and connect the switch. Automatic return switch (momentary switch).
These grcoves can b used for fnmly fixing the tying ba.ds or lad wis oi the auto switch, etc., dd also termiml boards, etc-, to the main body of the cylinder q " l-f9 -l lF'rg _1+T l---' l I I Detailed drawing ol part a Detailed drawing of part b Part a Patl a Ff"frf?
B Contact output signal 3 selected alarm Sets the alarm selected for the contact output signal 3.
W&F Contact B OUT6 N/A Output signal: OFF (open) for normal operation 4 OUT1 to OUT6 Contact A, B Output signal A: Contact A, B: Contact B Same as above Used to display the 5 [Enter] key MESSAGE screen to accept the setting. Used to display the MESSAGE screen to initialize the settings of RUN, REMOTE, and 6 [Initial] key OUT1 to OUT6. 7 [Cancel] key Used to cancel the setting.
4 5 6 7 8 9 10 L1 28 44 60 76 92 108 124 140 156 172 L2 40 56 72 88 104 120 136 152 168 184 L3 50 72 88 104 120 136 168 168 184 200 EXHAUST ADAPTOR LOCATION B .Both Ends FOR FURTHER TECHNICAL DETAILS ON THIS PRODUCT REQUEST CATALOG REFERENCE N400
A B 18 - 43 Timing diagram (Example) The figure shows the timing diagram of operation for the selected step data input type and the PLC parallel input/ output signals used when power is supplied.
(b) Moisture in the refrigerant circuit (colour of the indicator) Green (DRY) ---Good Yellow (WET) ---Moisture is present in the refrigerant.
Single unit Note 1) Port exhaust B Ejector system t Pressure Sensor/Digital Pressure Switch for Vacuum Specifications Common Silencer exhaust Pressure sensor C Type Pressure range [kPa] Specifications Symbol P 0 to 101 Analog output 1 to 5 V Pressure sensor For manifold T Analog output 1 to 5 V 100 to 100 Individual port exhaust A B C D E F H J K Q R S Unit selection function Note 9) NPN
(b) Moisture in the refrigerant circuit (colour of the indicator) Green (DRY) ---Good Yellow (WET) ---Moisture is present in the refrigerant.
IO-Link communication and power supply connector layout (Port Class B) BUS IN: M12 5-pin plug, A-coded No.
(See Fig. b) : Each bit status, 0 or 1, of the data shows the ON or OFF solenoid valve status (0: OFF, 1: ON), and the output number starting from 0 will be assigned to from the lowest bit of the memory data.
A B C D E F G H LAT3-10 10 49 4 60 50 4 10.5 LAT3-20 20 69 6 25 90 80 14 20.5 LAT3-30 30 89 6 25 120 110 24 30.5 13 - LAT3-50 Note 1) Refer to Mounting screw specifications and tightening torques in section 4.3 Mounting (P.24). Note 2) The length of the part of the dowel pin inserted into the positioning hole should be shorter than the specified depth.
2 M4 x 0.7 x 8 Nickel plated JIS B 2805 Nominal 6 Chromated Cross-recessed head cap screw E type snap ring Handle Ring Lock nut Needle O-ring Chromated Chromated JIS B 2401 P12 Replacement Parts No. Description Material Parts no. Valve Spring Seal NBR, Stainless steel o !0 !
For safety operation of SMC Refrigerated Air Dryer, read thoroughly and follow stated safety instructions, as well as regulation stated within ISO 4414*1 & JIS B 8370*2. *1) ISO 4414: Pneumatic fluid power General rules and safety requirements for systems and their components *2) JIS B 8370: Pneumatic fluid power General rules relating to systems This manual explains about installation
Model: 10 (Side Ported), Number of Cores - Lead Wires: L2 (17 Cores), Lead Wire Length: 2 (1.5m), Valve Stations: 8 Stations, P, E Port Locations: B (Both Sides), SUP/EXH Block: R (External Pilot), A, B Port Size: C6 (ø6 One-touch Fitting), Mounting: B (DIN Rail Mounting, Name Plate w/o Station Number)