Series LX Acceleration Time Guide The graphs are based on operation using an P/A DC power input type driver with halfstep energization.
Conduct an appropriate functional inspection after completing the maintenance. Do not use chemicals such as benzin and thinner to clean the product. SAFETY ( continued ) As the cables with connectors are used for all wirings among devices, the system complies with the IP65 environment.
Add an in front of the part numbers to have solenoid valves, etc. mounted on manifold.
Verify the specifications before use. 1 9 Specification 2 Specification Item Gateway distributed system 2 (128 points) specifications Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result.
Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof. Identification of flow rate range and standard or special product are displayed Tighten to the specified torque for piping. The tightening torque for connection threads is shown in the table below.
The assembly, operation and maintenance of machines or equipment including our products must be performed by an operator who is appropriately trained and experienced. 3.
When selecting an exhaust cleaner, refer to the selection method shown below, as the selection method will differ for exhaust from actuator drive systems, etc., and exhaust from ejectors, etc.
Blue section the operative DewPoint of the dryer is too low: freeze risk ; Green section operating conditions ensuring an optimal DewPoint ; Red section DewPoint of the dryer too high, the treatment of the compressed air may be improper.
Common external pilotP1 has an M5 screw. Stations Dimension 2 3 4 5 6 123 169 215 261 307 107 153 199 245 291 L1 L2 14-10-17
The cushion effect (smooth start-up, soft stop) is not available an intermediate stop or return from an intermediate stop using an external stopper, etc. When using an intermediate stop with the above information taken into account, implement measures to prevent particulate generation and set the operating pressure to no more than 0.3 MPa.
(M3 thread) (It is recommended to ground with resistance of 100 ohms or less) Power supply (0 VDC) 3 6 4 4 3 20 m or less total extension per branch Branch cable length Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof.
(This is to prevent the setting from remaining incomplete if, for instance, an operator were to leave during setting) : 3 step setting mode and Function selection mode are reflected on each other. 1 2 [ 50] 50 L/min (PFMB7102) [ 100] 100 L/min (PFMB7202) System error An internal data error has occurred. Turn the power OFF and turn it ON again.
If using the product in an interlocking circuit: Provide a double interlocking system, for example a mechanical system. Check the product regularly for proper operation. Otherwise malfunction can result, causing an accident.
Otherwise an injury can result. Approx. 1 second M3 x 8 L Water proof seal (accesorys) Measurement mode 4 L/min 40 L/min 100 L/min 16 L/min 250 L/min Panel Be sure to select the correct sensor to be connected. Caution *: The panel mount adapter can be rotated through 90 degrees for mounting. *: The panel mount adapter should be fixed firmly with screws.
If using the product in an interlocking circuit: Provide a double interlocking system, for example a mechanical system. Check the product regularly for proper operation. Otherwise malfunction can result, causing an accident.
Install an after-cooler, air dryer or water separator, etc. Air containing excessive drainage can cause malfunction of valves and other pneumatic equipment. To prevent this, install an after-cooler, air dryer or water separator, etc.
Black (DC) Without an electric signal for the solenoid valve the manual override is used for switching the main valve. Locking type (Tool required) is available as an option. Red (DC) Blue 100 VAC 110 VAC 200 VAC 220 VAC Red Blue 100 VAC 110 VAC Red 200 VAC 220 VAC Push type (Tool required) Push down on the manual override button with a small screwdriver until it stops.