CJP M15 x 1.5 4 10 20 23.5 17 15 27 30.5 24 5 14.5 19 11.5 15 19 4.5 M22 x 1.5 5 10 20.5 25 17.5 15 27 31.5 24 Note) E and F should be machined in a concentric manner.
BMA3-050S (A set of a, b, c, e) BMA3-063S (A set of a, b, c, e) Auto switch Switch bracket (Resin) Transparent (Nylon)Note 1) d e White (PBT) c Switch holder b Auto switch mounting screw a * Band (a) is mounted so that the projected part is on the internal side (contact side with the tube).
Determination of load's kinetic energy (E) E > Es E Es Determination of bore size Review of larger bore size E = m E 2 a ( ) 2 = (Refer to page 1548.) 1000 P Ps P > Ps Determination of pressure for intermediate stop (p) (Refer to page 1548.)
Wn Mass mn X-axis xn xa xb xc xd Y-axis yn ya yb yc yd Z-axis zn za zb zc zd X 1 mt = x (mn x xn)w Wa Wb Wc Wd ma mb mc md Y 1 mt = x (mn x yn)e D1 mt = x {mn x (A + zn)} r Z -X (n = a,b,c,d) Refer to the following sections 1 to 4 to calculate the center of gravity and the total load.
RB No. of piping surface Head cover Piping surface Operating direction Left Right r Front G H t Head cover WR Side w Head cover WL Side C D e Bottom E F y q J Bottom K L Front A B I DJ Note 1) The 6 types of tcentralized piping shown above are available in centralized piping model.
M15 x 1.5 4 10 20 23.5 17 15 27 30.5 24 5 14.5 19 11.5 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com 15 19 4.5 M22 x 1.5 5 10 20.5 25 17.5 15 27 31.5 24 Note) E and F should be machined in a concentric manner.
Hard anodized Aluminum alloy Cylinder tube q Anodized Aluminum alloy Collar w Chromated Aluminum alloy Piston e Stainless steel Piston rod r Phosphate coated Snap ring Carbon tool steel t Nickel plated Rod end nut Carbon steel y Replacement Parts: Seal Kit Chromated Aluminum alloy Spacer for switch type u Urethane Bumper A i Bore size (mm) 12 16 20 25 Kit no.
A B C D E F A B C D E F G H Pressure port Pressure port Right Left Left Right Left Right Right Left Left Right Right Left Left Right Operating direction Operating direction There are 9 possible reciprocating piping methods. There are 16 possible reciprocating piping methods.
supply field wireable connector (7/8 inch) q End Plate Bracket e Reinforcing Brace This bracket is used for the end plate of DIN rail mounting.
q IN OUT t e q r IN OUT w r w AR30(K)-B/AR40(K)-B q t AR50(K)-B/AR60(K)-B e IN OUT q t r w e IN OUT r w Component Parts No.
When speCllylng mor e than one option, please tisl numerically Ihen atphabetically.
Plug (Prepared by customer) L N E [Accessory] Power supply connector N Earth leakage breaker (Secondary side) E L Cable Crimped terminal (Prepared by customer) N E (Earth) L Cable size : 14AWG Wire tightening torque : 0.5Nm Fig. 3-5 Power supply cable 3.3 Installation HRS Series 3-10 HRX-OM-R016 Chapter 3 Transport and Setting Up Wiring 1.
Table 3.8-2 RTU mode message frame Address c)Function d)Data e)Checksum a)Start b)Device (CRC) f)End T1-T2-T3-T4 XX XX XX XX XX XX T1-T2-T3-T4 a) Start In Modbus RTU mode, message frames are separated by a silent interval (noncommunication time).
E E E E E E E KF flange F F F Fn n n n (KF) () Heater (option) Auto switch H H H H J J J J G G G G B B B B A A A A A A A A Model A B C D E Fn G H J K XLC-25 50 120 48 1 12 40 26 39 27.5 8 XLC-40 65 171 66 2 11 55 41 63 36 9 8 XL-OMO0001-A 5 Guaranteed period and range The warranty period is 2 million cycles (under SMC endurance test conditions), 18 months after delivery or 12 months in service
The tightening torque of the M3 screw must be 0.35 to 0.45 Nm. t The detection position can be changed under the conditions in step e. Auto switch y Confirm where the mounting position is, and tighten the auto switch fixing screw (M2.5) to fix the auto switch mounting nut. The tightening torque of the M2.5 screw must be 0.25 to 0.35 Nm.
YU-03 J E T1 B 2-D through 2-O counter bore (mm) Bore size (mm) B D E J M O Part no. Joints 12 7 25 9 34 11.5, depth 7.5 YB-03 32, 40 K ( across flats) 12 9 32 11 42 14.5, depth 8.5 YB-05 50, 63 H (with locking) 16 11 38 13 52 18, depth 12 YB-08 80 d2 d1 19 14 50 17 62 21, depth 14 YB-10 100 L UT Weight (g) Bore size (mm) C UA RS W T1 T2 V Part no.
Pilot valve assembly for VG342 Valve option Light/Surge voltage suppressor Standard type Nil Energy-saving type Y Nil None Continuous duty type E S With surge voltage suppressor (Grommet type is only available.)
For other kits, order E type control unit.
YU-03 J E T1 B 2-D through 2-O counter bore (mm) Bore size (mm) B D E J M O Part no. Joints 12 7 25 9 34 11.5, depth 7.5 YB-03 32, 40 K ( across flats) 12 9 32 11 42 14.5, depth 8.5 YB-05 50, 63 H (with locking) 16 11 38 13 52 18, depth 12 YB-08 80 d2 d1 19 14 50 17 62 21, depth 14 YB-10 100 L UT Weight (g) Bore size (mm) C UA RS W T1 T2 V Part no.
YA 03 Applicable air cylinder bore size mm 03 05 32, 40 50 Bore size (mm) B D E F M T1 T2 Part no.