ZSE30A(F)/ISE30A Power-saving function Power consumption is reduced by turning off the monitor. (Reduce power consumption by up to 20%.)
8, and can be ordered by using the seal kit number corresponding to each bore size.
Do not scratch or gouge the linear guide by striking it with other objects. 3. Since the slide table is supported by precision bearings, do not apply strong impacts or excessive moment when mounting workpieces. 4. The cylinder can be operated by directly applying a load within the allowable range.
A circuit in which power is supplied by the secondary coil of a transformer that meets the following conditions. Maximum voltage (with no load): 30 [Vrms] (42.4 [V peak]) or less Maximum current: 1. 8 [A] or less (including when short circuited) 2. Limited by circuit protector (such as fuse) with the following ratings Caution 1.
Select it by referring to Allowable Stroke Speed below. SpeedWork Load Graph/Required Conditions for Regeneration Option(Guide) LEFS25/Ball Screw Drive Horizontal Vertical 30 20 Use a regeneration option.
The zero clear range varies by 1%F.S. due to variation between individual products. Release the applied pressure to atmospheric pressure, and retry the zero clear operation. Check that the above-mentioned preparation work has been performed correctly, and part A shown in the figure is pushed by hand and makes temporary connection.
This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switch-mode power supply and the product or by using a series power supply instead of a switch-mode power supply. Peak/Bottom value display The maximum (minimum) flow from when the power was supplied to this moment is detected and updated.
Screw is prepared by customer.
Press the button once to decrease by one digit, press and hold to continuously decrease.
The assembly, operation and maintenance of machines or equipment including our products must be performed by an operator who is appropriately trained and experienced. 3.
Measurement instruments that SMC manufactures or sells have not been qualified by type approval tests relevant to the metrology (measurement) laws of each country. Therefore, SMC products cannot be used for business or certification ordained by the metrology (measurement) laws of each country.
Handling of One-touch Fittings Maintenance Precautions on Tube by Other Manufactures Caution Caution Warning 1.
Release the lock by pulling the pressure regulator knob out. If the knob is turned by force damage will occur. After adjusting the pressure, lock the knob again by pressing it back down. 2. Adjust pressure in an upward direction. A correct pressure setting cannot be achieved by adjusting the pressure downward.
There is a danger of sudden action by air cylinders if sliding parts of machinery are twisted and changes in forces occur. In such cases, human injury may occur, e.g., by catching hands or feet in the machinery, or damage to the machinery itself may occur. Therefore, the machine should be adjusted to operate smoothly and designed to avoid such dangers. 2.
Release the lock by pulling the pressure regulator knob out. If the knob is turned by force damage will occur. After adjusting the pressure, lock the knob again by pressing it back down. 2. Adjust pressure in an upward direction. A correct pressure setting cannot be achieved by adjusting the pressure downward.
V100 SY Non-locking push type (Tool required) SYJ VK VZ Pin Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com It is turned ON by pushing the button in the direction indicated by the arrow until it hits the end and is turned OFF by releasing the button.
Order a valve by adding the external pilot specifications [R] to the part number. Inch-size One-touch fittings and NPT/NPTF/G threads are available.
Displacement at the section indicated by the arrow when a load is applied to this section with the slide table fully extended.
Zero point adiustment is performed by varyrng lhe tenston force of the zero adjustng sping. Block Diagram Operation [-ie When reverse action isrequired, change lhe shatt ol the span adjusting lever to the oppogrte side and connect output pressure to ouT 2.
A Pressure Type (NVEP) which controls secondary pressure by varying the current through the solenoid. 2.