Table of Contents CU Length is shortened by approx. 64% max. Volume is reduced by approx. 70% max.
Operate the cylinder securing it by its plates, not by securing it by its slide block. 3. The clearance between the slide block and the plate at the stroke end is approximately 1 mm to 6 mm. It could be extremely dangerous, as there is the risk of getting your fingers caught. Install a cover as necessary. 4.
Tighten the union nuts on both sides equally by hand. A watertight seal can be obtained by hand tightening. LVN Never use a pipe wrench etc., as it may break the product. Table 1 shows the tightening torque for reference. LQHB Table 1 Tightening Torque of Union Nut TL TIL 6.
In this case, move the dust cover at the neck of the stud by the finger or twist the stud slightly left or right to break in the dust cover before use.
Measurement instruments that SMC manufactures or sells have not been qualified by type approval tests relevant to the metrology (measurement) laws of each country. Therefore, SMC products cannot be used for business or certification ordained by the metrology (measurement) laws of each country. Revision history Bore sizes 40, 50, 63 added. TR Edition B Both ends tapped mounting added.
customer PLC Provided by customer PLC Provided by customer PLC Provided by customer Provided by customer PLC IO-Link master Communication plug connector for DeviceNet p. 7 p. 7 Communication plug connector for IO-Link JXC-CD-T JXC-CD-S Straight type JXC-CL-S Straight type T-branch type (Accessory) To SI To ENC To SI To MOT To PWR Provided by customer Communication cable Power supply for
It should be provided by the customer. 2 Joint and modular adapter are shipped together with the product. 6 EX245 Series Specic Product Precautions 1 Be sure to read this before handling the products.
For standard installation, turn 15 to 30 using tool, after fastening by hand. Pay attention not to over torque the product.
Press the button once to increase by one digit, and press it continuously to keep increasing the set value. Press the button once to decrease by one digit, and press it continuously to keep decreasing the set value. Press the button to finish the setting. 1.0 to 1.2 Yellow ZS-28-C-1 Turn the power off and turn it on again.
Afterwards, it is possible to adjust the value by pressing UP or DOWN button. (3) Press the SET button to complete the setting. The pressure switch turns on within a set pressure range (from P1L to P1H) during window comparator mode.
Width across flats of attachment With across flats of the main port Tighten the connector by hand.
This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switch-mode power supply and the product, or by using a series power supply instead of a switch-mode power supply. To set this function, refer to SMC website (URL http://www.smcworld.com) for more detailed information or contact us.
During an emergency when the air supply is cut off, it is used to alleviate a problem by forcibly pushing the release piston back to release the lock. However, take note that the sliding resistance of the piston rod will be high compared to unlocking with air pressure. 2.
To invert the position, contact SMC. q Make sure not to apply to the slide block a load that exceeds the value that has been calculated in the selection procedure. w Operate the cylinder securing it by its plates, not by securing it by its slide block. e The clearance between the slide block and the plate at the stroke end is approximately 1mm to 6mm.
In addition, when atmospheric pressure is desired, shut off the power after reducing the set pressure, and then introduce atmospheric pressure by using a vacuum release valve, etc. i If the power for this product is cut off by a power failure, etc. when it is in a controlled state, the setting side pressure will be held temporarily.
Body ported (Individual pilot exhaust) VZ42 20 Rc 1/4 Instruct by specifying the valves, blanking plate option to be mounted on the manifold along with the manifold base model no. And for the order of valves installation or options position, instruct separately by the manifold specification sheet.
Output always supplied by high pressure inlet.
1 manually counterclockwise lowers piston u, which pushes open the seal created by seal !0, thus allowing the condensate to drain out. Turning drain cock !1 manually counterclockwise lowers piston u, which pushes open the seal created by seal !
This is affected by factors such as leakage in piping, consumption by drain valves and pilot valves, and reduction of air volume due to temperature drops.
Features 5 Series LJ1 Electric Actuator Basic Configuration Examples Teaching box Dedicated controller Electric actuator Controller setup software (option) PC (provided by customer) 24VDC power supply (provided by customer) PLC (provided by customer) Can be operated with the electric actuator, dedicated controller, teaching box and 24VDCNote 1) power supply.