<br>Note 1) Do not disassemble the shaft trunnion type because assembly accuracy is required. <br>Note 2) MB series seal kits come with a grease pack.

<br>A signal is output when there has been no numerical change for a certain period of time, so this signal can be used to indicate when the cylinder has stopped. <br>This function is useful for detecting the push position or resetting the value at the cylinder origin position.

<br>For the manufacturable stroke range, refer to the “Cylinder Stroke” section in the catalog. <br>The CE1 and CEP1 series catalogs can be found here.

<br><br>

<br>However, bottom side (head side) flanges are not available. <br>For bottom mounting, use the special order part number suffix “-XC82” that eliminates the need for relief machining of the guide during mounting. (Note that the selectable bearing types and strokes are limited for this type.)

<br>Note) For the ball bushing type, a high-precision type can be selected for both standard MGP and MGPW series cylinders. <br>The MGPW series catalog can be found here.

<br>When ordering an individual auto switch, prefix a “D-” to the part number.<br>As the CDQ2B32-30DMZ-M9BW is a cylinder with 2 auto switches, be sure to order 2 D-M9BW auto switches if 2 are needed.

<br>The solid state auto switches listed in the “Applicable Auto Switch” tables are all available as standard. Reed auto switches are available as a special order.<br>The special order options are shown at the end of the solid state auto switch catalog, which can be found here.

<br>If the power is turned ON without a load connected to the auto switch, an overcurrent will flow and the auto switch will be instantly damaged.

<br>・Production of the new D-M9□(W)(V) auto switch commenced in June 2016, and production of the new D-M9□(W)(A) auto switch commenced in September 2016.

<br>For example, the outer diameter of the cylinder tube differs between the JCM series and the CM2 series.<br>For use with a non-JCM series cylinder, proper auto switch operation verification is required.

<br>For more information, refer to the D-MP□ series catalog or the video below.<br>A video about the D-MP□ series features and applications can be seen here.

<br>It allows for the selection of the optimal rotary actuator size by inputting the necessary parameters.<br>The “Rotary Actuator Model Selection Software” can be found here.

<br>Select the desired range (“-XC12” to “-XC15”) and add the corresponding suffix to the end of the CDRQ2BSP40-90 part number. Check the catalog for details on the “-XC12” to “-XC15” suffixes as the position of the start and end points vary.<br>The CRQ2 series catalog can be found here.

<br>The change of rotating range special order option changes the position of the start and end points, with the angle adjustment range remaining ±5°.<br>The CRQ2 series catalog can be found here.

<br><br>

<br>However, there is no clean room specification for the CRB2-Z and CRB series.<br>The 10-CRB1 and 21-CRB1 series catalog can be found here.

<br>The part number for the standard lithium soap based grease packs are “GR-S-010” (10 g) and “GR-S-020” (20 g).<br>The part numbers for the fluorine grease packs (special order part number suffix “-XC30”) are “GR-F-005” (5 g) and “GR-F-050” (50 g).

<br>For example, for the MHZ2 series it indicates the finger option. And for the MHL2 and MHF2 series, it indicates the opening/closing stroke. <br>For details, refer to the "How to Order" section in the web catalog of each series. The parallel type air gripper catalogs can be found here.

<br><br>