Air cylinder As the indicator LED protrudes from the switch unit, mounting the switch bracket above the LED may cause damage to it. (4) Insert the auto switch mounting screw (M3) included in accessories from the mounting hole of the auto switch mounting band, inserting the through hole of the switch bracket.
After checking the detection position, tighten M3 screws to fix the auto switch so that the bottom of the auto switch contact the cylinder tube. (The tightening torque of the M3 screw must be 0.5 to 0.7Nm.) Tighten the auto switch mounting screw(M4) to fix the auto switch mounting bracket.
Nm N M1 M M3 W W2 W W4 ML2B25 10.0 1.2 3.0 200.0 58.0 65.0 100.0 ML2B32 20.0 2.4 6.0 300.0 80.0 96.0 150.0 ML2B40 40.0 4.8 12.0 500.0 106.0 140.0 250.0 ML2B25 ML2B32 ML2B40 J 0.43 0.68 1.21 18 ML2B/M1 ML2B/W1 ML2B/W1 0 0 0 Nm 0 0 0 N N 0 m/s m/s m/s ML2B/M2 ML2B/W2 ML2B/W2 N m N N m/s ML2B/M3 m/s m/s 20 ML2B/W3 ML2B/W3 10 Nm 5 3 2 1 N N m/s m/s m/s ML2B/W4 500 N 00 N
After checking the detection position, tighten M3 screws to fix the auto switch so that the bottom of the auto switch contact the cylinder tube. (The tightening torque of the M3 screw must be 0.5 to 0.7Nm.) Tighten the auto switch mounting screw(M4) to fix the auto switch mounting bracket.
Model Bolt Max.tightening Torgue (Nm) JMHZ2-16D M3 x 0.5 0.59 Attachment 21 - How to Mount Air Gripper (1)Mounting orientation: On robot arm(s) (2)Mounting to the cover Take care not to get the switch cable caught when mounting the cover.
JXC-OMU0026 Part A Part B Holding screw M5X14 (2) Grounding Fit the grounding cable with crimped terminal between the M3 screw and shakeproof washer as shown below and tighten the screw. M3 screw Shakeproof washer Grounding cable (with crimped terminal) Caution The cable with crimped terminal and shakeproof washer must be prepared by the user.
Screw size: M3 Tightening torque: 0.72 [N m] 11 10 11.
Reference data Units: mm IDH6 Jumper cord 7 6 5 4 3 1 PE Remote start/stop Fault-signal (N.O: Close at "Fault") Fault-signal (N.C: Open at "Fault") 1042 31 N 2 L Operation-signal (N.O) Ground Terminal screw: M3 Suitable wire: 1.25mm or more 2 244 Power supply Connector width: 6.5mm or less Detail of wiring 35 184 172 392 (Note) 15 80 223 321 3001 485 The type without built-in filter does
Piping to products When piping to a product, avoid mistakes regarding the supply port, etc. 1) When using SMCs M3 or M5 fittings, follow the procedures below to tighten them. Mounting Connection thread: M3 1. Operation manual Warning First, tighten by hand, then use a suitable wrench to tighten the hexagonal portion of the body an additional 1/4 turn.
Replacement procedure of shock absorber Loosen the hexagon socket head set screw (M3) at the piston rod by approximately one turn, and push down the lever. (See Fig. 11) Tool Hexagon wrench: Width across flats 1.5mm While pushing down the lever, remove the shock absorber and replace it with a new shock absorber. Tighten the hexagon socket head set screw (M3 x 0.5) of the piston rod.
(M3 thread) (It is recommended to ground with resistance of 100 ohms or less) Accessories Hexagon socket head cap screw (M3 x 30): 2 pcs. Connects the SI unit and the valve manifold. Seal cap: 1 pc.
JXC-OMT0002-C Part A Part B Holding screw M5X14 (2) Grounding Fit the grounding cable with crimped terminal between the M3 screw and shakeproof washer as shown below and tighten the screw. Shakeproof washer Grounding cable (with crimped terminal) M3 screw Caution The cable with crimped terminal and shakeproof washer must be prepared by the user.
(Appropriate tightening torque: 0.4 to 0.6Nm) Part A Part B Holding screw M5X14 (2) Grounding Fit the grounding cable with crimped terminal between the M3 screw and shakeproof washer as shown below and tighten the screw. Shakeproof washer Grounding cable (with crimped terminal) M3 screw Caution The cable with crimped terminal and shakeproof washer must be prepared by the user.
As the indicator LED protrudes from the switch unit, mounting the switch bracket above the LED may cause damage to it. (4) Insert the auto switch mounting screw (M3) included in accessories from the mounting hole of the auto switch mounting band, inserting the through hole of the switch bracket.
) (LEMC/LEMH/LEMHT) T slots Model Bolt Max. tightening Effective length torque [Nm] [mm] LEMC25 LEMH25 M3 0.63 45 LEMC32 LEMH32 M5 3.0 68 LEMHT25 M4 1.5 67 LEMHT32 M6 5.2 810 -39- effective length of it to enter from the bottom. 5.
Screw Max. tightening torque (Nm) Maximum screw-in depth (mm) MHZ2-6 MHZJ2-6 M3 x 0.5 0.88 10 MHZA2-6 MHZAJ2-6 Model No. Screw Max. tightening torque (Nm) MHZ2-6 MHZJ2-6 M2.5x0.45 0.49 MHZA2-6 MHZAJ2-6 8 - Caution 1. Avoid twisting the gripper when mounting an attachment. Any damage to the gripper may cause malfunction and reduce the accuracy. 2. Avoid external force to fingers.
Description Note Material Bracket set 1 SFD-BR100 With 2 countersunk head screws (M3) IDK e AMG AFF SFD200-C Component Parts No. Description Note Material AM Element 1 PC, Polyolefin, PU o !
) M2 M3 M1 M2 1.25 1.68 Slide 12 3 0.53 0.70 Ball bushing 3.34 4.25 Slide 16 7 1.53 2.11 Ball bushing 11.4 17.1 Slide l l 20 12 5.60 7.28 Ball bushing Note) For the purpose of calculating the moment, the length of the arm is the distance that is measured from the guide shaft center ( mark).
Dimensions L A LA Attached from top W C PA MM Note 1) M F HB HA Note 2) Attached from bottom: MD R Body B (mm) Note 1) Note 2) B C F HA HB L LA MM MD M PA R W A Model CY3B15 CY3B20 CY3B25 CY3B32 CY3B40 16 35 6.5 5.5 16.5 23 57 25 M4 x 0.7 M3 4 25 6 36 18 36 6.5 5.5 17 23.5 66 30 M4 x 0.7 M3 4 27 6 37 20 46 8.0 5.5 21 28.5 70 30 M5 x 0.8 M4 5 36 7 47 22.5 60 9.5 6.0 27.5 36 80 35 M6 x 1.0
Compressed air 1.0MPa Fluid Max. operating pressure Min. operating pressure (1) 0.05MPa 1.5MPa Proof pressure Ambient and fluid temperature Filtration rating 5 to 60C 0.01m(95% particle size collection) Oil mist removal rate Max.0.1mg/m3 (ANR) (2) (At saturation of element oil, less than 0.01mg/m3(ANR){0.008ppm}) 2 years or when pressure drop reaches 0.1MPa Element life Note 1) With N.O.auto