MHF2 mg F F Gripping force at least 10 to 20 times the work piece weight The "10 to 20 times or more of the work piece weight" recommended by SMC is calculated with the safety margin of a = 4, which allows for impacts that occur during normal transportation, etc. 2F mg Number of fingers and therefore, mg F 2 x With "a" as the safety margin, F is determined as follows: mg F = x a 2 x When
G) Mounting at the back (G) Mounting at the front (F) Rear double clevis D Head side single clevis style (C) Head side double clevis style (D) Bore (mm) E1 EB L MR AO L1 UW UF E2 R W MF ZF FB CD XD UB CB EW TR AT XA SA AH AB XV TL h14 TD TM TF Z H9 h14 H14 0.5 1.2 e8 h14 Max. 157 Max. 195 Max. 238 Max. 290 90 115 135 165 45 60 70 80 20 20 25 25 245 280 300 330 16 18 22 26 25 30 30 40 Max
10mA load current) Internal voltage drop Leakage current 100A or less at 24VDC 0.8mA or less at 24VDC Operating position .
As a guide, it should be turned about 90 past the point at which tightening can be felt. 9-9-23
Select function by the iconized menu at the first page.
unit (F) E P F Model ZX100 K6 Circuit diagram (Circuits other than those with vacuum switch are shown as below.)
27NO.ZL3-OM00701-A [F 3] Response time Select the response time of the switch output.
Setting of [F 3] Response time completed. 26 -
NO. ZQ-OM01501 [F 4] Auto-preset function This function calculates and sets the pressure values automatically based on the on-going operation.
Normal output Pressure setting Sets the ON or OFF point of the switch output. -70 kPa(P_1) Hysteresis Set the hysteresis to prevent chattering. 10 kPa(H_1) [F 2] Setting of OUT2 See page 27 Item Description Default setting Pilot valve for supply at signal ON Sets the ON point of the supply pilot valve signal 5 kPa(H_2) Supply pilot valve at signal OFF Sets the OFF point of the supply pilot
Magnet With auto switch only 9 Magnet plate Stainless steel With auto switch only 10 Scraper 11 Rod seal 12 Piston seal NBR 13 Tube gasket 14 Piston gasket 269 CHKD Series Dimensions Basic type/CHKDB 2 x Rc P F with effective thread depth G F with effective thread depth G Q Q Width across flats f c R D R a b g e H E E h + Stroke C B + Stroke 4 x K through 8 x L counter bore 4 x K through
26No.TQ0010298-OM003-B [F 3] Response time Select the response time of the switch output.
) 14 (10) 32 (0) 50 (10) 68 (20) 86 (30) Atmospheric pressure dew point F (C) How to read the dew point conversion chart Example) To obtain the atmospheric pressure dew point at a pressure dew point 50F (10C) and a pressure 102 psi (0.7 MPa). 1.
Displacement of Section A when force acts on Section F Displacement of Section A when force acts on Section F F A F Guide central axis (1 axis type) F For the double axis type, this is the cylinders central axis.
Leakage is kept at the lowest level by using VCR and Swedgelok fittings.
Order Made Note) When an auto switch is installed at an intermediate position of a type with auto switch, keep the maximum piston speed at 300 mm/s or below to ensure operation of relays or other devices.
Test conditions Detection nozzle: 1.5 Piping: F type 4 x 2.5 tube/G, H type 6 x 4 tube Supply pressure: 200 kPa Response time when the workpiece is set at 90% distance Response time for close contact of workpiece ISA3-G ISA3-H ISA3-F Piping length: 1 m Piping length: 1 m Piping length: 1 m 2.0 2.0 2.0 Response time [sec] Response time [sec] Response time [sec] 1.5 1.5 1.5 1.0 1.0 1.0 0.5
Residence time of water at 20C is 5.5 x 10-6 sec, whereas at 150C, it is 2.8 x 10-8 sec, or about 200 times shorter. The objective of baking is to exhaust water with long adsorption residence time more quickly. XVD Surface leakage This leakage occurs between surfaces of the sealing and the seal material.
10 mA (2 V or less at 40 mA) Internal voltage drop 100 A or less at 24 VDC 0.8 mA or less Leakage current Operating range .
F E Y2 F Y2 CRQ2X MSQX L L E MRQ 2 x Q4 2 x Q4 K K C B D G D G B C U H U H M T N M T 25.5 N (34.5: Connector type) 2 x R 1 2 x R Auto switch P P W1 W Auto switch Size: 20, 30 Size: 40 W W 2 67 8 15 8 When D-M9m is used 32.5 1.
Calculation of applied lateral load F F = N m g (N) = 0.2 x 10 x 0.1 x 9.8 = 2.1 (N) 1. Calculation of applied lateral load The lateral load F equals the total load of the work piece. Thus, F= 5 x 0.05 x 9.8 = 2.5 (N) 70 Lateral load F (N) 60 0.4MPa 50 40 2. Confirmation of allowable lateral load From the graph, the allowable lateral load at L=50mm and P=0.4MPa is 18N. 2.