Solid State Auto Switch Do not use in direct sunlight. 10. Do not mount the product in locations where it is exposed to radiant heat. 11. Take appropriate measures against the lightning surge on the equipment side as the auto switches do not have any lightning surge resistance specified in the CE/UKCA marking. 12. Do not use in environments subject to radiation stress.
Do not torque it more than required in case to operate a lock type manual.
The received message is deleted if the calculation result and received CRC do not match.
Do not use the product where these are present.
PA07 . 17 4.6 Auto tuning modePr.PA08 . 18 4.7 Input signal automatic on selectionPD01 . 18 4.8 Parameter setting by MR Configurator2TM . 19 4.8.1 Parameter reading . 20 4.8.2 Parameter setting (Ex. Control mode change) . 20 5.
Do not use pressure sensors with corrosive and/or flammable gases. 7. The applicable fluids are air, non-corrosive gas and non-flammable gas. Consult with SMC if the switch is to be used with other types of fluids. Caution Connection Caution 1. Do not drop, bump, or apply excessive impacts (100 m/s2) while handling.
Do not attempt to rotate the connector, as it is not rotatable.
HRR Series 3.1 Precautions wiring communication 3-1 HRX-OM-W004 Chapter 3 Serial communication 2 2 R D R D 3 3 S D S D 5 5 S G S G Master This product Do not connect any wire to other PIN numbers.
are used 200 200 When 20 units are used 77% reduction Current model IR3000 Series 91% reduction 38000 yen reduction 150 150 117000 yen reduction Current model IR1000 Series IR2000 Series 100 100 IR1000-A Series IR2000-A Series IR3000-A Series 50 50 0 0 0 10 20 30 40 50 0 10 20 30 40 50 Units used Units used Released into atmosphere IR Special bleeding structure No fixed throttle in the new
Note 4) Option H (Auto-drain bowl type: Metal bowl) is only applicable to the IDFA6E-20.
D-X Individual -X Bore size (mm) Symbol S Z 5 19.5 10 28.5 15 37.5 20 46.5 5 40 10 49 15 58 20 67 Stroke Technical data 4 19
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate or set with wet hands. This may lead to an electric shock. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Do not connect wires while the power is on. Otherwise it can break the circuit inside the Auto switch causing malfunction. Do not lay wires or cables with power cable or high-voltage cable in the same wiring route.
I-MU02 I-MU03 I-MU04 I-MU05 CNS E1 16 18 20 28 A1 10.5 12 14 18 MM M10 x 1.25 M12 x 1.25 M14 x 1.5 M18 x 1.5 A1 10.5 12 14 18 L1 27 31 36 46 E1 14 18 20 28 L1 27 31 36 46 MM M10 x 1.25 M12 x 1.25 M14 x 1.5 M18 x 1.5 NDH10 8 10 10 14 Size 25 32 40 50 Size 25 32 40 50 +0.058 0 +0.058 0 +0.058 0 +0.070 0 CLS CLQ Applicable pin no.
acting/Spring extend (mm) C95 A B A B Bore size Auto switch model Bore size Auto switch model Hs Hs C92 25 50 75 100 125 150 200 25 50 75 100 125 150 200 All strokes All strokes 20 25 32 40 20 25 32 40 20 25 32 40 20 25 32 40 20 25 32 40 20 25 32 40 20 25 32 40 20 25 32 40 20 25 32 40 20 25 32 40 20 25 32 40 20 25 32 40 D-C7 D-C7 55 55 80 80 105 24.5 (27) 45.5 45.5 70.5 70.5 95.5 24.5
Caution Do not touch the terminals and connectors while the power is on. Otherwise electric shock, malfunction or damage to the product can result. Nominal thread size Tightening torque Rc(NPT)3/8 15 to 20 Nm Do not touch the piping or its connected parts when the fluid is at high temperature. It may lead to burnt. Ensure the piping cools sufficiently before touching.
Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these . 2. Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction. 3. Do not use in a place subject to heavy vibration and/or shock. 4.
Do not use in an atmosphere where corrosive gases, chemicals, sea water, water, or water steam is present. Do not use in cases where there is direct contact with any of the above. 2. Do not use in a place subject to heavy vibration and/or impact. 3. Do not use in an environment where flammable gas or explosive gas is present. Usage may cause a fire or explosion.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.