MLGC 70 4 104 Rc 1/8 Rc 1/8 62 7 7 40 125 60 32 M8 x 1.25 13 38 M12 x 1.75 depth 21 115 11 82.5 4 115 67 8 8 45 150 75 38 M8 x 1.25 14 47 WH W X Y T U V W Z Bore size (mm) 20 25 32 40 30 23 30 112 146 182 16 53 50 30 25 37 132 167 199 20 63 60 25 28.5 37 132 167 202 60 20 63 20 33 44 162 210 227 25 73 70 Without Rear Plate Stroke range (mm) Long Stroke Bore size (mm) 20 25 32 40 Bore size (mm
(8.3-2O0OHz) o External Pilot Tape,/ NVJ300R An external pilot supply is required when main valve pressures are lower than 20 PSl.
(8.3-2O0OHz) o External Pilot Tape,/ NVJ300R An external pilot supply is required when main valve pressures are lower than 20 PSl.
(8.3-2O0OHz) o External Pilot Tape,/ NVJ300R An external pilot supply is required when main valve pressures are lower than 20 PSl.
16 53 30* 112 30 146 182 MGC 25 60 20 63 132 167 199 30* 37 60 20 132 63 167 202 37 28.5 25* MGF 70 25 73 162 44 210 227 33 20* CY1 Without rear plate Long stroke Bore size (mm) Bore size (mm) Stroke range (mm) Z R Y MY1 20 25 32 40 20 25 32 40 250 to 400 190 14 129 350 to 500 207 14 146 350 to 600 210 14 146 350 to 800 236 15 191 Note) Dimensions marked with "*" are not required for back
20 2-M6 thread depth 11 2-M6 thread depth 11 15 15 35 18 15 2-M6 thread depth 11 2-M6 thread depth 11 20 20 A 17 17 40 A 20 20 15 45 60 25 45 60 A Applicable clamp cylinder A Applicable clamp cylinder Part no.
(Roll moment) Moment MXW25 120 70 (Static moment/Dynamic moment) Allowable Moment MXW25 70 100 50 (Nm) 30 40 Maximum moment (Nm) Maximum moment (Nm) 50 MXW20 25 30 40 Roll moment Pitch moment Yaw moment MXW20 20 Model Mr Mp/Mep My/Mey 15 MXW16 20 MXW16 12 10 15 3 5 5 MXW8 7 10 MXW12 MXW12 2 10 10 MXW12 4 5 7 5 4 3 12 20 20 MXW16 MXW8 MXW8 3 2.5 25 40 40 MXW20 2 2 1.5 50 100 200 300 500 65
Otherwise, injury or an accident may occur. 20 - 5. Do not put hands, etc. in between the air gripper fingers or attachments. Otherwise, injury or an accident may occur. 6. When removing the air gripper, first confirm that no workpieces are being held and then release the compressed air before removing the air gripper.
Note 5) The system accuracy when combined with an applicable flow sensor.
AXT100-20-2-05 AXT100-20-2-06 AXT100-20-2-01 AXT100-20-2-02 AXT100-20-2-03 AXT100-20-2-04 Valve Mounting VS After confirming the gasket is correctly placed under the valve, tighten the mounting screws with the appropriate torque listed below.
Can be locked in both directions An equal holding force can be obtained on either reciprocating stroke of the cylinder. Compact lock unit is light weight and saves space Overall length has been reduced by using an independent brake cylinder (15% compared to P/A products).
Series REAL Size: 10, 15, 20, 25, 32, 40 To ensure a permanent path. When smoother operation is required, even with an eccentric load. Stable operation is possible even with an eccentric load, through the use of a ball bushing. Series REAH Size: 10, 15, 20, 25, 32 The use of a linear guide makes possible a large load, large moment and high precision.
110 110 130 180 Q 26 28 28 34 34 50 50 60 76 R 4.5 5 5 5 5 9 9 10 12 S 1.6 2.0 2.0 2.3 2.3 3.2 3.2 4.5 4.5 5.5 6 6 7 7 9 9 9 11 159 172 178 204 210 225 232 259 311 13 13 16 16 19 19 22 22 32 100 113 119 145 151 166 173 200 253 63 76 76 90 90 106 106 122 160 20 20 20 20 20 20 20 20 20 63 76 76 90 90 106 106 122 160 10 10 10 10 10 10 10 10 10 1 8 1 4 3 8 AMG150 , , 1 4 3 8 , AMG250 1 2 3 8
The cushion effect (smooth start-up, soft stop) is not available an intermediate stop or return from an intermediate stop using an external stopper, etc. When using an intermediate stop with the above information taken into account, implement measures to prevent particulate generation and set the operating pressure to no more than 0.3 MPa.
This is included in the response from the product when there is an error in the received request. 9 NAK(15h) Error content is included in the response when there is an error in the received request. Refer to the table below for exception codes.
(Refer to 2.3.1 Setting of contact input signal type and form) If an input from an external switch is detected, it can be generated as an alarm.Options to select continuous monitoring or monitoring during operation are available. Also, the detection start time after the start of operation and the detection end time can be set.
If the power should not come back on, please contact SMC for an inspection.
mm Lead 150 Slide screw 20 mm Lead 500 10 mm Lead Ball screw Horizontal specification Maximum speed 1000 600 500 930 740 20 mm Lead 100W mm/s 500 Slide screw 20 mm Lead 180 10 mm Lead Ball screw 100W Nm Rated thrust 90 20 mm Lead 50 Slide screw 20 mm Lead Rolled 0.05 Repeatable positioning accuracy Ball screw Ground 0.02 mm 0.1 Rolled Slide screw Motor output Horizontal specification
Since the lock may be released due to reverse exhaust pressure flow, use an individual exhaust type manifold or single type valve. 4. Branch off the compressed air piping for the lock unit between the cylinder and the speed controller. Use of an external branch may cause a reduction in service life. 5.