Vacuum Pad Measurement instruments that SMC manufactures or sells have not been qualified by type approval tests relevant to the metrology (measurement) laws of each country. Therefore, SMC products cannot be used for business or certification ordained by the metrology (measurement) laws of each country.
Conventional system Speed control by a flow control valve which can variable throttle flow according to indicated current. Shock absorber Multistage speed control by combining speed controllers and a directional control valve.
Applicable auto switch Reed switch Solid state switch Strokes are available in 5 mm increments by installing spacers Description MI W S in standard stroke cylinders.
CJ1 Bushing (Bearing) fR Reference: Even under a light load, if the piston rod has been stopped by an external stopper at the extending side of the cylinder, the maximum force generated by the cylinder will act upon the cylinder itself.
This product can be used as a regulator with a check valve by installing it between solenoid valve and actuator. Maintenance Warning 1. Make sure to perform a periodic inspection of the pressure gauge when it is used by installing it between solenoid valve and actuator, etc. Sudden pressure changes could happen and the durability of the product could be reduced.
When no by-pass piping is used (when the product is used for emergency stops), solenoids for unlocking are necessary. For detailed information, please refer to "Pneumatic Circuit" in Specific Product Precautions on page 9-12-3. Applicable Auto Switch/Refer to page 9-15-11 for further information on auto switches.
Measurement instruments that SMC manufactures or sells have not been qualified by type approval tests relevant to the metrology (measurement) laws of each country. Therefore, SMC products cannot be used for business or certification ordained by the metrology (measurement) laws of each country.
Purchase orders are available in units of 10 pieces. d Pilot port block disk By installing a pilot port block disk in the pilot passage of a manifold valve, it can be function as an internal pilot/external pilot mixed manifold. (Use in combination with a SUP or EXH block disk.)
INP output signal 1) Positioning operation When the product comes within the set range by step data [In position], the INP output signal will turn on. Initial value: Set to [0.50] or higher. LEJ Select a suitable actuator by work load and allowable moment.
Note 3) Distinction between meter-out/meter-in types by appearance. Those are distinguished by the lock nut. The meter-out type is zinc chromated (the round lock nut is electroless nickel plated), while the meter-in type is black zinc chromate plated. Note 4) AS120, AS1400, AS220, AS320: Brass parts are electroless nickel plated, provided as standard.
If no problem is caused by this setting, keep these settings. Pressurizing error Move on to the switch output NPN/PNP specification switching setting. Press the button to set.
the value shown in the graph at 400 mm/s by the coefficient listed in the table below.
Note 3) Intermediate stroke is available by the 1 mm interval.
Then reinstall the stopper lever and parallel pin in their original positions and secure in place by tightening with the three bolts . MHS MHC MHT 6. Reinstall the rotary unit in its original position and secure in place by tightening with the four bolts .
The air pressure that flows in acts on diaphragm C and while opposing the force generated by diaphragm B it also acts on diaphragm A opposing the compression force of the setting spring and becomes the set pressure.
In case it is displaced, please return it to the right position by pushing the external mover by hand (or pushing the piston mover with air pressure). 11. In vertical operation, be careful about dislocation of the magnet coupling. Note that the mover may drop off due to dislocation of the magnet coupling if pressure or load beyond the specification is applied. 12.
Base mounted stacking type q Remove the clip and metal joint from the position where the new station is to be mounted by pulling them in the directions indicated by the arrows. w Place the additional manifold block assembly and mount the metal joint and clip by reversing the assembly order.
Simple and unencumbered appearance by adopting round-shaped cord.
Wiring specifications Connections begin with the A side solenoid of the first station being connected to terminal no. 1, and continue in the order indicated by the arrows in the drawing without skipping any terminals.
The overall Cv of a tube and valve system is calculated by combining the Cv of each element as follows: 1 Cv 2 syst 1 Cv1 2 1 Cv2 2 1 Cv3 2 etc Quick approximate calculation can be made by assuming 50% of system pressure drop is made at the valve and 50% in the tube system.