Vacuum Module Series ZX Therefore, do not use it with or expose it to the following chemicals: paint thinner, carbon tetrachloride, chloroform, acetic ester, aniline, cyclohexane, trichloroethylene, sulfuric acid, lactic acid, water-soluble cutting oil (alkalinic), etc. 2. Do not expose it to direct sunlight.
Do not disassemble, except for when replacing any of the replaceable parts, as this may cause the performance to deteriorate. (8) Proximity switch output The switch output signal is output near the clamping end and the unclamping end respectively.
Type 20) 3 110 VAC, 50/60 Hz Nil Push type (Safety style) G H L LN L plug connector With lead wire 600 mm lead wire 300 mm lead wire 4 220 VAC, 50/60 Hz Grommet B Locking type (Tool required) 2 Body side exhaust (Type 30, 50) 5 24 VDC 6 12 VDC C Locking type (Manual) Without lead wire Without connector With lead wire Without lead wire Without connector MO With connector D Without connector DO
No.6 No.5 No.8 No.7 No.10 No.9 Red flashing Wrong switch setting, Parameter writing error Green On Bus-off state, Duplicate MAC ID 16 32 4 8 1 2 Red flashing Off Green On I/O Connection is in the Timed-Out state Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Specifications Specifications AFF2B to 75B Applicable model AFF2B to 37B Applicable model Refer to How to Order for standard specifications on pages 14-20-10, 16, 23, 31, 37 and 43. Refer to How to Order for standard specifications on pages 14-20-3, 10 and 16.
Do not make any modifications to be product. Do not take the product apart. Piping Caution 1. Before piping Make sure that all debris, cutting oil, dust, etc, are removed from the piping. 2. Wrapping of pipe tape When screwing piping or fittings into ports, ensure that chips from the pipe threads or sealing material do not get inside the piping.
Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water vapor, or where there is direct contact with any of these. 2. Do not use in explosive atmospheres. 3. Do not use in locations subject to vibration or impact. 4. Do not use in locations where radiated heat will be received from nearby heat sources. 5.
Do not apply excessive force or impact. This will not only damage the product but also decrease its performance and life expectancy. It is not possible to disassemble the bonnet assembly of this product. If the components and assembly are damaged, or damage is expected, exchange the bonnet assembly itself. Do not disassemble the parts that are not explained in this operation manual.
Refer to pages 16-14-3 to 16-14-4 for Safety Instructions and Common Precautions on the products mentioned in this catalog, and refer to pages 16-1-11 to 16-113 for Precautions on every series. q u w e 1 3 LOW i o 2 4 r Selection !0 t Caution !1 1. Select the model taking into consideration the material suitable for the operating fluid.
Mounting from upper side l l Model Bolt Maximum tightening torque (Nm) l (mm) MGF 40 MGF 63 MGF100 M6 x 1 10 7.5 M8 x 1.25 25 9 M10 x 1.5 51 9 Mounting from bottom side Do not bring objects that are sensitive to magnetism near the cylinder. There is a magnetic built into the cylinder. Do not bring magnetic disks, cards, or tapes near the cylinder. Data may be lost.
Connect End Plate and tighten removed screws by specified tightening torque. (0.6 Nm) Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Note 1. The power supply should be off while setting the switches. 2.
Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof.
Do not use the filter regulator where containing those. Effects organic solvents and chemicals, and where these elements are likely to adhere to the equipment.
Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not operate in locations where vibration or impact occurs. 3. In locations which receive direct sunlight, provide a protective cover, etc. 4. In locations near heat sources, block off any radiated heat. 5.
Do not use the back pressure regulator as shutoff valve or safety valve. 2.
Do not use in an atmosphere containing corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction. 3. Low-frequency operation 3.
Note) Do not pull on the lead wires with excessive force. This can cause faulty and/or broken contacts.
Do not disassemble the product or make any modifications, including additional machining. Doing so may cause human injury and/or an accident. 14.
Do not make any modifications to be product. Do not take the product apart. Piping Caution 1. Before piping Make sure that all debris, cutting oil, dust, etc, are removed from the piping. 2. Wrapping of pipe tape When screwing piping or fittings into ports, ensure that chips from the pipe threads or sealing material do not get inside the piping.
Do not disassemble and modify. It may result in the trouble, malfunction, fire, etc. 2. Do not touch for a while when being energized or after cutting off the power source because it is high temperature. 3.