Body Size: -, Thread: -, Port Size: -, Mounting: -, Bowl: -, Lubricant Exhaust Port: -, Flow Direction: -, Pressure Unit: -

energy saving effect

Height 1710 x Width 1185 x Depth 955 HRSH150-Al-A 268 HRSH200-Al-A HRSH250-Al-A HRSH300-Al-A 344 Height 2020 x Width 1230 x Depth 1040 HRSH100-Wl-A 197 Height 1610 x Width 925 x Depth 955 HRSH150-Wl-A 227 HRSH200-Wl-A HRSH250-Wl-A Mounting/Installation Warning 2.

Thermo-chiller

x Width 925 x Depth 955] HRS150-W -20-A 459 [208] HRS150-A-20 A> 4.

HRS100/150

231 Height 1710 x Width 1185 x Depth 955 HRS150-Al-l-A 237 HRS100-Wl-l-A 205 Height 1610 x Width 925 x Depth 955 HRS150-Wl-l-A 208 IDH Forklift insertion side HRS150-A-20 A> 4.

53

Use this as a reference.

33

x Depth 580 HRSE018-A-23 HRSE024-A-23 HRSE012-A-23-T 48 Height 790 x Width 470 x Depth 580 HRSE018-A-23-T HRSE024-A-23-T IDH Selection Warning 1.

Lightweight and Compact

Use this as a reference.

Old AL series lubricators from old AC series modular F.R.L. units (2 digits: AL□□) can be replaced with lubricators from the AL□□-A series, which are interchangeable.
In addition, old AL series lubricators (e.g., AL3000-02) from older AC series modular F.R.L. units (4 digits: AL□□□□) can be replaced with lubricators from the AL□□-A series (AL30-02-A).

Case: [Resin] Polycarbonate Case, Drain Exhaust: -, Case Guard: -, Specification: Applicable part number: AL20-A, AL30-A, AL40-A, AL40-06-A, AL50-A, AL60-A, Type: Sight dome assembly

Refer to the table below for the storage capacity of AL-A/AL-D series lubricators.
A 1000 cm2 tank type is available for standard AL30 to 60 series products.
Details on the 1000 cm2 tank type can be found <a href="/webcatalog/en-jp/seriesList/?type=GUIDE&id=AL-A-E" target="_blank">herea>.

VQ7-6/7-8

Rc1/4 Rc3/8 Bottom Note) When equipped with control unit, 1 or 2 stations are used for mounting. 6 Series VQ7-6 DIN Connector Type VV71-100 80 2n-Rc1/4, 3/8 100 80 9 37 9 23 14 U side 15 R4.5 Manual override Indicator light R4.5 53.5 P=43 9 9 53.5 P=43 20 9 23 38 B B B B B B B B B SMC SMC SMC A PA PA PA PA A A A A B A L1 L2 L2 L1 B A B SMC A B A 4n-Rc1/4, 3/8 (ports A, B) PA L side R side

Secondary Batteries

(Normally closed) A N.O.

Conforming to ISO Standard Solenoid Valve (with M12 Connector) Series EVS7-6/7-8/7-10 (Size 1) (Size 2) (Size 3) 1

P = 43 PA 23 A A B B 14 12 A PA PA L1 L2 L2 L1 B B B 14 12 A A A A B 14 A A PA B B (2n 1/8) 4n-1/4, 3/8 2, 4 port PA L-side R-side L-side R-side D-side D-side 89 3 89 16 141 (Single) 141 (Single) 55 44 186 (Double) 186 (Double) 196 (3 position) 196 (3 position) 77.5 Bottom ported M12 connector L: Dimensions n: Stations 141.5 L n 1 Formula 2 3 4 5 6 7 8 9 10 121 5 1 12 14 PA PB 107 L1 = 43n

For AL30-A to AL60-A series lubricators, when the lubrication plug is opened under the pressure of the lubricator, air bubbles may be generated at the end of the oil passage (sometimes they are not). This is also caused by the bowl’s internal pressure being lower than the outlet pressure.

BOWL ASSEMBLY, AL30-A, AIRLINE EQUIPMENT, AF MASS PRO, 21, AF MASS PRO NO SIZE RATING, 0.22046 lb

The AL30/40/50/60 are equipped with a check valve on the body.
Therefore, lubricant can be supplied by removing the lubrication plug even when the product is pressurized.
Loosen the lubrication plug slowly, by about 1 turn, to release the pressure inside the bowl.
When pressure in the bowl is released, remove the lubrication plug and supply lubricant.

The AL bowl (size 30 and 40) is covered with a transparent bowl guard, allowing 360 monitoring.?The oil drop rate is adjustable depending on equipment requirements.

Case: -, Drain Exhaust: -, Case Guard: -, Specification: Applicable part number: AL30-A, Type: Damper holding assembly

Case: [Resin] Resin, Drain Exhaust: -, Case Guard: -, Specification: Applicable part number: AL30-A, Type: Damper (assembly)

Case: -, Drain Exhaust: -, Case Guard: -, Specification: Applicable part number: AL30-A, Type: Lubrication plug assembly