EX120/121/122 Note 4) Since this is a special product, a manifold part number is not specified.
(A contact) 50 75 100 125 150 50mm 75mm 100mm 125mm 150mm Use a driver with CE marking. N.O.
VXD2 Z 1A VXD2 Z 3 0 A A VXK Enter standard product number.
Next, pour water at 5 to 40C, then measure the flow rate with a pressure difference of 0.075 MPa. However, the pressure difference needs to be set with a large enough difference so that the Reynolds number does not go below a range of 4 x 104 . By substituting the measurement results for formula (8) to figure out Av.
2 A 2 A 24 VDC 0.63 A 1 A 1 A Temperature rise*5 25C 25C 25C 1 Leakage: The value at a differential pressure of 0.01 MPa or higher and an ambient temperature of 20C 2 This product has an IP67 enclosure, but if water enters the product, it may result in malfunction or breakage.
For a facility having a small installation area (that can not vent the air naturally): Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level. 3.
Mineral oil A A A C A A 18 Sodium hypochlorite (2%, Room temperature) A C D A D B 19 Sodium chloride A A A A B 20 Carbon dioxide A A A A A A 21 Natural gas A A A A A A 22 Boric acid A B D A A B 23 Unless noted otherwise, the solution concentration is in a saturated state.
If driving a load such as a relay that generates a surge voltage,
Option Symbol and Configuration Fluid and Options Option symbol Seal material Coil insulation Body, Shading coil material Option symbol and body material Brass SUS304 F L X F, B L, J B J B J J T A H A H A H D N G, J S Q E P V M Y A H K K A H A H B J V M V M Y D, E N, P B J Fluid(Application) Standard A B C D E F NBR FPM Argon Argon(long life) Ethyl Alcohol Ethylene glycol Ozone(low
Mineral oil A C A A A A 18 Sodium hypochlorite (2%, Room temperature) A C A D D B 19 Sodium chloride A A A A B 20 Carbon dioxide A A A A A A 21 Natural gas A A A A A A 22 Boric acid A B A D A B 23 Unless noted otherwise, the solution concentration is in a saturated state.
, are Nil, A, B, D, E, Z. 3 Available for air and water. 270 IN OUT C 3 A 3 A 6 D 1 Available for the VXZ A to 2 .
1 1 1 1 2 (a) (a) (b) (c) (a) (b) (c) (b) (c) (a) (b) (c) (a) (b) (c) (b) (c) (a) (b) (c) (b) (c) (a) (b) (c) Note 1) The above (a), (b), (c) indicate heater mounting positions.
Since a large quantity of liquid will be pumped out, use a suitable throttle in the discharge port if problems occur. Note 3) With a low number of operating cycles, even a valve with a small Cv factor can be operated.
n k d r a i n p o r t Rotates 360.
(A contact) N.O. (A contact) Number of auto switches N.O. (A contact) N.O. (A contact) 1 2 1 pc. 2 pcs. 6 6 pcs.
In the case of 0.8MPa, when port A is a vacuum, port P can be pressurized to 0.8MPa (7kgf/cmG).
Stabilize the source pressure by providing a tank and a vacuum regulator. Provide a vacuum switch valve to individual lines.
To prevent danger and damage due to a breakdown or malfunction of these products, which may occur at a certain probability, a backup system should be arranged in advance by using a multiple-layered structure or by making a fail-safe equipment design, etc. 5.
To prevent danger and damage due to a breakdown or malfunction of these products, which may occur at a certain probability, a backup system should be arranged in advance by using a multiple-layered structure or by making a fail-safe equipment design, etc. 13. Avoid heat radiation from strong heat sources, such as direct sunlight or a hot furnace.