CL low speeds or for intermediate stops, just like a hydraulic unit, while using pneumatic equipment such as a valve.
These plugs are not available for a standard One-touch fittings Series KQ. If trying to install the plug into a KQ, plug will jump out of the fitting. Note the exclusive marking for self-seal fittings before use. The Number of Insertions and Removals from Self-seal Fitting Caution qThe number of insertions and removals as a rough quide is as follows.
Assembly of a bracket and 2 mounting screws. *4 Refer to chemical data on page 46 for chemical resistance of the bowl. *5 A bowl guard is provided as standard equipment (polycarbonate). *6 A bowl guard is provided as standard equipment (nylon). *7 Without a valve function *8 The combination of metal bowl: 2 is not available. *9 For pipe thread type: NPT.
B 1.5 29 11 11 5.1 5.1 9.5 A B 26 10.5 26 10.5 H G (NN 1) x H B-B A-A (mm) Model F 45 40 48 58 42 55 50 55 62 N 4 4 4 4 6 6 8 8 8 G 22 22 22 22 17 18 37 56 H 46 46 46 56 56 56 59 62 NN 2 2 2 2 3 3 4 4 4 GA 18 18 18 22 48 73 74 96 118 HA 50 50 50 56 48 56 112 118 124 I 16 16 16 16 18 23 25 18 21 J 46 46 46 56 72 100 155 190 215 K 31 41 51 61 71 96 121 146 171 KA 126 183 211 239 NA 4 4 4
LJ I I~ ,L (mm) ;A . .8 (mm) Model ZPY40B 'A 40 .8 G:M6Xl G:M8 Xl.25 .K .L G:M6Xl F K L Y Model A B C 0 E F 0 E Y C F F 43 34 62 44 16 24.4 46 ~.to 13 12162642 6 ZPY50B 50 53 38 ,46 66 ' 8 12.4 . 57 19.~ 15 . . 5 6 16 18 2C 3C 46 . tube tube P R tube, ' 412.51 14.5 .8 tube; <:11/41 le.5 W , tube, " 12.51 14.5 1.8 , tube. '6/41 16.5 7 2.5 31 Specifications .
To accomplish this, use a device such as a highly responsive electric control circuit or solenoid valve, and place the solenoid valve as close as possible to the cylinder. 4. Note that the stopping accuracy will be influenced by changes in piston speed.
25 14 14 20 30 30 32 14 14 20 30 30 32 28 28 40 60 60 64 50 12.5 CS1 64 16.5 80 23.5 C76 80 23.5 119 28.5 Note) For a double clevis, a pin (cotter pin) and a flat washer are equipped as standard.
Pad Caution Guide for drop prevention Provide an auxiliary device (example: a guide for preventing the workpieces from dropping) as necessary. Mounting Position As a rule, the unit must be installed horizontally.
To accomplish this, use a device such as a highly responsive electric control circuit or solenoid valve, and place the solenoid valve as close as possible to the cylinder. 4. Note that the stopping accuracy will be influenced by changes in piston speed.
Perform inspections on a regular basis as necessary, such as at the beginning of an operation, to make sure that the mechanical valve operates properly. Failure to observe this precaution could lead to unsafe operation, such as unintended operation or malfunction.
In order to further improve stopping accuracy, the time from the stop signal to the operation of the lock should be shortened as much as possible. To accomplish this, use a device such as a highly responsive electric control circuit or solenoid valve driven by direct current, and place the solenoid valve as close as possible to the cylinder. 4.
Note 9) The copper and fluorine-free specification is available as a standard product.
Use caution when handling a cylinder, which is running at a high speed and a high frequency, because the surface of a cylinder tube could get so hot enough as to cause you get burned. 4. Do not use the air cylinder as an air-hydro cylinder. If it uses turbine oil in place of fluids for cylinder, it may result in oil leak. 5.
Model Model Note 2) Since vibration may increase with low speed operation, use 2mm/s or more as a guide for speed. LC6C-220AD (Refer to page 309 for details.)
same side as the A, B port.
back flow mechanism as a standard feature.
A B C A B A B A B A B 15A 20A 25A Note 1) For each piping diameter for each body size, the second and later numbers or symbols indicate reducing.
When tightening the auto switch mounting screw, use a watchmakers screw driver with a handle diameter of about 5 to 6mm. Furthermore, use a tightening torque of 0.05 to 0.1 Nm. As a rule, it should be turned about 90 from the point at which tightening can be felt. Use a tightening torque of 1 to 1.2 Nm for the hexagon socket head set screws (M4 x 0.7). 1.