0 . 8 , M 6 x 1 Nr4 x 0.7, N,ls x 0.8 s1O-s16 M 5 x 0 . 8 , M 6 x 1 Mls x 0.8, M6 x 1 a20-a32 M6 x 1, M8 x 1 M5 x 0.8, M6 x 1, M8 x 1.25 ..aAO=s5O', M 6 x 1 , M B x 1 M 6 x 1 , M 8 x 1 . 2 5 \4q,r'tirc How to Order ZPY Pad dia.
136 154 50 22 53.5 94 L1 Rod end nut 63 135 75, 100 Rear flange type: CLQG/CDLQG FV M Rear flange type (mm) 4-FD Without auto switch With auto switch Bore size (mm) FZ FX A + Stroke L FT B + Stroke G Stroke range FD FT FV FX FZ G L L1 M A A B B 36 91 10 to 50 63 101 46 9 9 80 92 108 38 8 33.5 60 46 101 75, 100 43.5 107.5 10 to 50 80 117.5 53.5 11 11 99 116 134 43 10 43.5 77 53.5 117.5 75
Electrical entry Grommet L plug connector M plug connector DIN terminal G L M D Applicable Auto Switch/Refer to page 10-20-1 for further information on auto switches.
M N 4-O T Q 2-P AH AG S K W U L B AL I 4-AK hole R AA AP J X AB A Y + Stroke V AI Z + Stroke AJ For 4-AO AG AN AI Cutout window 100 piston rod end connection AM Mounting dimensions For standard strokes (mm) Bore size (mm) Stroke range (mm) O N M L K J I B AP AO AN AM AL AK AJ AI AH AG AB AA P A 75, 100 125, 150 200, 250 300 63 80 100 M12 x 1.75 depth 23 100 66 180 135 117 65 228 60 M12 234
Use an air filter with 5 m or less filtration rating on the inlet side of the valve to avoid any damage to the seat caused by dust when mounting a 3 port valve for residual pressure release on the inlet side. 0.2 0.1 Piping 0 1000 2000 3000 0 Flow rate (/min (ANR)) Warning 1.
A water resistant type cylinder is recommended for use in an environment which requires water resistance. Lead wire length symbols: 0.5 m Nil (Example) M9NW 3 m L (Example) M9NWL 1 m M (Example) M9NWM 5 m Z (Example) M9NWZ Solid state auto switches marked with are produced upon receipt of order.
IDFmF-m-K IDF4E to 75E IDFmE-m-L Refrigerant R407C (HFC) IDF F With a heavy-duty auto drain*1 (applicable to moderate pressure) IDF370D IDF370D-m-L IDU3E to 75E IDUmE-m-L With a motor type auto drain*2 IDF4E to 75E IDFmE-m-M p. 30 IDF190D, 240D IDFmD-m(-m)-M IDU3E to 75E IDUmE-m-M With a metal name plate IDF100F to 150F IDFmF-m-P p. 30 IDF4E to 75E IDFmE-m-R Refrigerant R407C (HFC) IDF D
M AR50, 60 AR30, 40 J G J G A A IN OUT IN OUT H M M H Parts list Material Note No.
The switches do not have an explosion proof rating. Never use in the presence of an explosive gas as this may cause a serious explosion. 2. Mount switches in locations where there is no vibration greater than 98 m/s2, or impact greater than 490 m/s2. 3. Do not use in an area where surges are generated.
Lead wire length symbols: 0.5 m Nil (Example) M9NW 1 m M (Example) M9NWM 3 m L (Example) M9NWL 5 m Z (Example) M9NWZ Since there are other applicable auto switches than listed above, refer to page 23 for details. For details about auto switches with pre-wired connector, refer to the Best Pneumatics No. 3. For the D-P3DWA, refer to the WEB catalog.
High Flow/ Power Saving Type Refer to page 46 for details.
Under certain circumstances, the use of an electronic style pressure gauge is recommended. 1.5-22 ARM1000/2000 Dimensions Dimensions A 4.5 4.5 B 25 34.5 C 34 43 D 21 28 E 18 27 F 56 70 G 16 20 H 9 11.5 J 18 24 K 19 28 M 52 66 P 9 11.5 Q 11.5 16.5 R 4.8 4.8 Symbol Model ARM1000 ARM2000 Dimensions by Number of Stations Manifold stations (n) Symbol Model 1 36 27 48 39 2 55 46 76 67 5 112 103
10.5 13 13 11 13 13 25 30 30 32 40 40 36 46 46 12 15 15 7 9 9 6.5 8.5 8.5 57 (65) 66 (74) 71 (79) 19.5 22.5 25 40 43 46 46 50 53 73.5 82 87 The figures in parentheses are the normally open type. 24 25 Series VX Safety Instructions The following safety instructions are intended to prevent a hazardous situation and/or equipment damage.
Standard Type: CXS Vertical mounting L L Mounting orientation m m up to 300 up to 400 up to 700 ( up to 800) up to 200 up to 600 up to 100 Max. speed (mm/s) Stroke (mm) All strokes 1 2 6 10 15 Selection graph 3 4 5 6 20 25 32 Horizontal mounting L Mounting orientation m m Refer to the caution notes below.
It is an assembly of a piston and a gasket (KSYP-13).
When in the locked state, do not apply a load accompanied by an impact shock, strong vibration or turning force, etc. Use caution, because an external action such as an impacting load, strong vibration or turning force, may damage the locking mechanism or reduce its life. 2. Consider stopping accuracy and the amount of over-run when an intermediate stop is performed.
When in the locked state, do not apply a load accompanied by an impact shock, strong vibration or turning force, etc. Use caution, because an external action such as an impacting load, strong vibration or turning force, may damage the locking mechanism or reduce its life. 2. Consider stopping accuracy and the amount of over-run when an intermediate stop is performed.
is thus 125 + 9.6 -135 m and the allowed 4p I r, *#P = 022 kPa / m r 3 5 m Relerring again to nomogram in fig 4.19: The pipe size line will now cut at almosl the same dia; a nominal bore pipe ot 65 mm, with an actual inner diameter ot 68 mm will be satistactory.