Speed Controller with Indicator In-line Brass Stainless steel Electroless nickel plated In-line Type “Made to Order” “Made to Order” section has been added. Pages 3, 8 section has been added. ¡Lubricant: Vaseline -X12 The numerical indication of ¡Greas L8 L8 x n pcs. + L16 x 2 + L26 x (n1) pcs. L8 x n pcs. + L17 x 2 + L26 x (n1) pcs. L8 L8 x n pcs. + L25 x 2 + L26 x (n1) pcs. L27 + L8/2 Bonnet Mounting surface Refer to page 6 for L8. The figure above shows the manifold with speed controllers connected using two DIN rail mounting brackets, adapters and a threaded stud kit for manifold.
Use the following UL approved products for DC power supply combinations. (1) Controlled voltage current circuit conforming to UL508 Circuit uses the secondary coil of an isolated transformer as the power supply, satisfying the following conditions.
Description Material Note 1 Body Spool Sleeve Spool valve Piston Pilot valve Aluminum die cast / Metal seal Stainless steel 2 Rubber seal / Aluminum NBR 3 4 Resin 33 Series VQZ Body Ported Type Dimensions: VQZ100 Dimensions: VQZ100 (mm) Valve Scale: 65% Grommet (G): VQZ115G -N1, N3, N7, M5 2-N1, N3, N7, M5 N1: One-touch fittings for 1/8" N3: One-touch fittings for 5/32" N7: One-touch fittings
Supply pressure verification Leak test P2(n1) > P1(n2) P2(n2) P1(n1) 10.0 to 101.0kPa CH Increases the set value 1 2 3 4 PRESSURE For normally closed P2(n1) > P1(n2) P2(n2) P1(n1) 0.1 to 1000.0MPa Decreases the set value SET P3(n3) and P4(n4) are the same as P1(n1) and P2(n2).
The cushion effect (smooth start-up, soft stop) cannot be obtained in an intermediate stop or return from an intermediate stop using an external stopper, etc.
an input/output signal of ON/OFF counter function.
Note 1) Values indicated by an asterisk () are optional.
Note) Please contact SMC when using an individual EXH spacer assembly, an individual SUP spacer assembly, an adapter plate assembly, or an interface regulator on 41P and 43P types.
Switching of valve is based on an electric signal from the connector. The valve coil is kept in a de-energized state even when there is an electric signal from the connector.
If the power should not come back on, please contact SMC for an inspection.
Install an after-cooler, air dryer or water separator, etc. Air that contains excessive drainage can cause malfunction of valves and other pneumatic equipment. To prevent this, install an after-cooler, air dryer or water separator, etc. 3. Use the product within the range of specifications for fluid and ambient temperature.
Please contact SMC for a specification sheet when placing an order.
Please contact SMC for a specification sheet when placing an order.
Note 2) An auto switch magnet is not attached. In cases where an auto switch magnet is attached, please add -M9// at the end of the part number. (Not available for high temperature models) Note 3) Auto switch and solenoid valve are not attached.
When an offset load is expected, provide a suitable mechanism such as a floating joint. 2) Use clean air (atmospheric pressure dew point temperature 10C or less). Use of a series AM mist separator (filtration rating of 0.3 m or less), or series AM + AMD (filtration rating of 0.01 m or less) is recommended.
When an offset load is expected, provide a suitable mechanism such as a floating joint. 2) Use clean air (atmospheric pressure dew point temperature 10C or less). Use of a series AM mist separator (filtration rating of 0.3 m or less), or series AM + AMD (filtration rating of 0.01 m or less) is recommended.
If the power should not come back on, please contact SMC for an inspection.
For details about silencers, refer to the AN series in the Best Pneumatics No. 7.
Bushing (Bearing) fR Reference: Even under a light load, if the piston rod has been stopped by an external stopper at the extending side of the cylinder, the maximum force generated by the cylinder will act upon the cylinder itself.
Precautions Plug a connector in or out vertically, never at an angle. Applicable cable O.D.: 3.5 to 7 (Reference) 0.5 mm2 2 core and 3 core wires equivalent to JIS C 3306 DC 24V 48V Caution No.2() Black () No.1(+) 1. Since this valve has slight air leakage, it can not be used for holding vacuum (including positive pressure holding) in the pressure container.