IZE11.eng If the installation is using accurate control, wait until the product has warmed up (approximately 20 to 30 minutes). 2 s button (DOWN) Easy setting Function selection mode Attaching the connector to the sensor wire Strip the sensor wire as shown to the right. (Do not strip the wire insulation) 20 mm or more Cover Output OUT1 LED (Green): LED is ON when OUT1 is ON.
Note1) To avoid the damage of O-ring and adjustment part, do not turn bypass valve adjusting bolt(13) farther than the point where turning is stopped at both ends. Note2) Do not apply pressure to the operation port during adjustment. Note3) Bypass valve is fully open at ex-factory.
20 20 0.15MPa 0.15MPa 0.15MPa 10 10 10 0.2MPa 0.2MPa 0.2MPa 100 200 300 0 100 200 300 0 100 200 300 0 Detection distance (m) Detection distance (m) Detection distance (m) Example 1) When requiring 300m detection, select the detection nozzle of 1.0 with supply pressure 0.2MPa.
Front mount type l l l Model Bolt Max. tightening torque Nm Max. screw-in depth (l mm) Model Bolt Max. tightening torque Nm Body thickness (l mm) LXS M6 x 1 7.4 13 LXS M6 x 1 7.4 20 Use bolts at least 0.5mm shorter than the maximum screw-in depth, so they do not touch the body. Caution 2. Through holes 2.
Do you have a process requiring cost-efficient automation? Do you have a new series of safety features to implement? In fact, do you need another pair of hands in order to solve that troublesome domestic project?
Function selection mode Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Reset applied pressure to a level within the set pressure range.
Function selection mode Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. seconds, to display [F 0]. Select to display the function to be changed [F].
The maximum operating 0 5 10 15 20 25 30 ( temperature for the valve is 150oC. If the heater temperature is over 200oC or valve temperature is Time (sec.) Duration of the inrush current flow (as a guide) over 150oC, please use thermostat to control the heaters to prevent overheating.
Do not twist the valve seal 1.
Also, do not use the product in an environment where corrosive gases, chemicals, liquid can come in contact with its outside surface.
Pin Allocation 4 Over current protection Yes 1 UT1 Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. SF and BF Indicators Yes Over current detection 2 DI (Input signal "n+4") FS LED 3 1 BF SF Description 3 0V (US1) Fieldbus Do not operate the product outside of the specifications.
Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not operate in locations where vibration or impact occurs. 3. In locations which receive direct sunlight, provide a protective cover, etc. 4. In locations near heat sources, block off any radiated heat. 5.
Customers do not need to apply for a license to use this equipment. Be sure to comply with the following precautions. Do not disassemble or modify the product. Disassembly and modification are prohibited by law.
If you do not do this air-bleeding, there would be the great danger of unexpected accident, such as shooting out of parts when they are being unscrewed.
Do not Do not use in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. The product is not designed to be explosion proof. Do not Do not use the product in a place where static electricity is a problem. Otherwise failure or malfunction of the system can result.
Do not use these for pneumatic operations because they will lead to oil leaks.
Then with one side fixed, gradually close the other side and measure 2R at the point where the tubing folds or flattens, etc. 2R Fixed side How to Order Burst pressure drop curve 1.0 TL0604 Metric sizes 20 Burst pressure drop coefficient 0.8 TIL01 20 Inch sizes 0.6 Length Applicable to both metric and inch size 0.4 Tubing Model Symbol 10 20 50 100 Type Length 10 m 0.2 20 m Roll 50 m 0 20
o.s, ercept dyo6.. op.Btins PEssubs: 28" vacuum 0 PStc {20 Kgt/cnf)' NVS/tl|-4 Prssure Fanoe: 28" vacul 3@ rlc {20 Kgrcnti) Lakage: Irort lo pon (nt.maD not to .xce.d 0.005 coblc fl pr hinut at 1@ PstG (6.7 toam) Mel4islr: all houshc !6n. atumhum d|6 cas|ngg $oor arld stc@ a40F 61atnt6r. p.5rlvated ad hdtJoai.d lo 5a52 FE*wdl c 96* orlnot Blra N, sp&.r end dl.nl hou3in!
Then with one side fixed, gradually close the other side and measure 2R at the point where the tubing folds or flattens, etc. 2R Fixed side How to Order Burst pressure drop curve 1.0 TL0604 Metric sizes 20 Burst pressure drop coefficient 0.8 TIL01 20 Inch sizes 0.6 Length Applicable to both metric and inch size 0.4 Tubing Model Symbol 10 20 50 100 Type Length 10 m 0.2 20 m Roll 50 m 0 20
10 25 12 32 14 40 20 50 20 63 25 80 30 100 CC CC 36 125 36 140 40 160 45 180 50 200 60 250 70 300 Caution on Circuit Construction Surge pressure When the cylinder is operated at high speeds and reaches the stroke end, surge pressure could be created in the rod side or in the head side.