O Anal ogue out put Vol t age t ype Anal ogue out put Current ( si nk) t ype I TV 0 1 I TV 0 4 O nl y use equi pm ent w i t h a m axi m um l oad i m pedance of 250 . O nl y use a equi pm ent w i t h a m i ni m um l oad i m pedance of 1k .
Anal ogue out put Vol t age t ype Anal ogue out put Current ( si nk) t ype I TV 0 1 I TV 0 4 O nl y use equi pm ent w i t h a m axi m um l oad i m pedance of 250 . O nl y use a equi pm ent w i t h a m i ni m um l oad i m pedance of 1k .
Replace the product with a new one right away when it reaches its life. Make sure to verify the operating conditions of the actuator at least once a day.
Anal ogue out put Vol t age t ype Anal ogue out put Current ( si nk) t ype I TV 0 1 I TV 0 4 O nl y use equi pm ent w i t h a m axi m um l oad i m pedance of 250 . O nl y use a equi pm ent w i t h a m i ni m um l oad i m pedance of 1k .
(mm) A B C D E F G H J L Port size Bracket part no.
7 w i t q Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com A A' @6 #2 @8 @9 #0 !8 !9 #1 @7 !4 !
slow speed from A to B due to the fixed throttle of the SSC valve.
Danger: Warning: CAUTION indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: DANGER indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. WARNING indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury.
DOWN OUT1 U P SET ZS-31-A Bracket Note: Mounting screws are not included.
(Pages 10, 12, 15, 17) L-Tees Combine an elbow with a Tee. Mixed sizes of barbed branches are available. (Pages 9, 11, 15, 17) V-Tees orient the barbed branches on adjacent hex surfaces. Mixed branch sizes are available. (Pages 10, 12, 15) 1/8 NPT Male manifolds Hundreds of combinations for the OEM needing a fitting that requires a minimum amount of labor to install.
A part B part Procedure Calculation Calculation example 1. Check the operating conditions, dimensions of attachment, etc. Operating model: MHY2-16D Opening time: 0.15 s a = 40 (mm) b = 7 (mm) c = 8 (mm) d = 5 (mm) e = 10 (mm) f = 12 (mm) A part a b c B part e f d 2.
(PD) + b (PD) = (Pr b) / a Pr PD a b [] a b MPa 0.00025 -0.25 kPa 0.25 -250 kgf/cm 2 0.002549 -2.549 ISE70 bar 0.0025 -2.5 psi 0.03626 -36.26 MPa 0.0004 -0.4 kPa 0.4 -400 kgf/cm 2 0.004079 -4.079 ISE71 bar 0.004 -4 psi 0.05802 -58.02 [] (ISE70 MPaPD=2000 ) Pr = a (PD) + b = 0.00025 2000 0.25 = 0.25[MPa] (ISE70 MPaPr=0.75[MPa]) (PD) = (Pr b) / a = [0.75 (-0.25)]/0.00025 = 4000 -63No.PS-OMV0003CN-G
DIN rail mounting adapter is mounted onto a screw mounting type controller afterwards.
There is a risk of unexpected malfunction. Do not use solvents such as benzene, thinner etc. to clean each unit. They could damage the surface of the body and erase the markings on the body. Use a soft cloth to remove stains. For heavy stains, use a cloth soaked with diluted neutral detergent and fully squeezed, then wipe up the stains again with a dry cloth.
Make sure to connect a speed controller and adjust it to a speed of 500 mm/s or less to operate the cylinder.
Make sure to connect a speed controller and adjust it to a speed of 500 mm/s or less to operate the cylinder.
M3x30 screw for connection to the valve manifold NS MS PWR PWR(V) WARNING indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury.
Press Part A by hand for temporary fixing. Press in the central part of Part A vertically with a tool such as pliers. A sensor connector cannot be taken apart for reuse once it is crimped. If the wire arrangement is incorrect or if the wire insertion fails, use a new sensor connector.
Note 2) Vibration resistance Conditions when tested with one sweep of 10 to 250 Hz in the axial direction and at a right angle to the armature, in both energized and deenergized states No malfunction occurred when tested.
Manifold mounting screw A Mounting manifold to DIN rail: 1) Hook the mounting hook on the "B" side of the manifold base to the DIN rail. 2) Push side "A" onto the DIN rail and tighten the clamp screw on the "A" side of the end plate.