Metering Valve with Silencer Series ASN2 This product cannot be used to hold a stop position for an extended period of time. Pilot check valves and actuators are not guaranteed for zero air leakage. Therefore, it is sometimes not possible to hold a stop position for an extended period of time. In the event that holding for an extended time is necessary, a mechanical means for holding should be devised. 3.
A flexible polyurethane tube is recommended when the lateral load is applied. 15-2-39
Series KS/KX Male connector: KSH (Standard) H (width across flats) Applicable Connection thread R Min. port size Effective area (mm2) Nylon Urethane
In order to prevent a malfunction or diaphragm damage caused by debris or cutting chips in the fluid, install a filter with approximately 100 mesh on the inlet side of a flow switch. C (COM) A (N.O.) Color of lead wire Black Symbol Contact C Z I SE3 Common A White Normally Open B (N.C.)
If the drain bowl is difficult to check and remove, it is recommended that a drain bowl with the auto-drain option be installed.
This product cannot be used as a check regulator by installing it between solenoid valve and actuator. 3. Port with a pressure gauge or a plug can be used as an OUT port.
A unique positioning mechanism allows accurate installation and removal of tubing with ease even in a hardto-see locations, while preventing piping errors when reconnecting. Plug Holder Socket Plug case Irregular shape permits engagement in a proper position.
To connect a drain discharge pipe, use a pipe with a minimum bore of 10, and a maximum length of 5 m. Avoid using a riser pipe.
If the drain bowl is difficult to check and remove, it is recommended that a drain bowl with the auto-drain option be installed.
Can be used for a wide range of pressures from low vacuum up to a pressure of 1.0 MPa. The use of a special profile ensures sealing and reduces resistance when the tube is inserted. Guide Collet Can be used in copper-free application. Body O-ring Flame resistance (Equivalent to UL-94 standard, material V-0) Stud Tube Effective when piping in a confined space.
Note 5) Without a valve function. Note 6) For NPT thread type.
Contacts/Bulb gland Pressure Source Nil W Nil B C 1a1b (Standard) 2ab Contact Warning Enclosure Type A 20a (Standard) Type A 20b Type A 20c Bulb gland 1.
Do not use in a low pressure application (such as a blower). F.R.L. unit has its own minimum operating pressure depending on the equipment and is designed specifically to function with compressed air. If used below the minimum operating pressure, a loss of performance and malfunction can occur. Please contact SMC if an application under such conditions cannot be avoided.
In such a case, adjust the open angle of its bleed valve to lower the pressure a bit inside the bowl, so that drainage will run through easily. Selection Caution 1. The maximum dischargeable drainage rate is 400 cc/min. If the product is operated in excess of this value, there is a risk of causing the drainage to flow over to the outlet side. Piping Caution 1.
Loosen the cross-recessed head machine screw by using a Phillips screwdriver to remove the plate from the case. 2. After exchanging connectors in desired places, fix the plate to the case by using a Phillips screwdriver. 3. After shifting the bolt for bracket to the outside, tighten the bolt by a Phillips screwdriver to fix the socket case.
If the drain bowl is difficult to check and remove, it is recommended that a drain bowl with the auto-drain option be installed.
All electrical work must be carried out in a safe manner by a qualified person in compliance with applicable national regulations. atmosphere. Do not mount in a location exposed to radiant heat.
21.5 (29.5) A B 20.5 (28.5) A B 15 (22.5) A B 17.5 (25.5) A B 19.5 (27.5) A B 18 (26) A B 16 (24) B 20 27.5 27 24.5 31 25.5 27.5 29 27 24 30 21.5 (29.5) 20.5 (28.5) 15 (22.5) 17.5 (25.5) 19.5 (27.5) 18 (26) 16 (24) 25 30 29.5 27 31 25.5 27.5 29 27 24 30 22.5 (30.5) 21.5 (29.5) 15.5 (23.5) 18.5 (26.5) 20.5 (28.5) 19 (27) 17 (25) 32 33.5 33 30.5 32 26.5 28.5 30 28 25 31 25 (34) 24 (33) 18 (
M E N S I O N S AD S E R I E S A U I T O D R A I N S S Y M B O L S H O W T O O R D E R A U T O D R A I N S E R I E S AD AD402-02 (1/4) PT AD402-03 (3/8) PT AD402-04 (1/2) PT AD600-06 (3/4) PT AD600-10 (1) PT H O W T O O R D E R A U T O D R A I N S E R I E S NAD NAD402-N02 (1/4) NPT NAD402-N03 (3/8) NPT NAD402-N04 (1/2) NPT NAD600-N06 (3/4) NPT NAD600-N10 (1) NPT FOR FURTHER TECHNICAL DETAILS
Cover (Option) Port A size No. of Port A Porting Port A Port B Model Port B size 10 tube 12 tube Rc Rc 6 tube 8 tube 6 tube 8 tube KRM11 One-touch fitting One-touch fitting 6, 10 1 4 3 8 KRM12 One-touch fitting Rc female thread 6, 10 Applicable Tubing Tubing material Tubing O.D.
9 i *1 *1 C95K32 A A-A A !2 !1 @4 Component Parts Description Aluminum die-casted Aluminum die-casted Aluminum alloy Stainless steel Aluminum alloy Rolled steel Rolled steel Oil impregnated sintered alloy Steel Steel for spring Carbon Steel Steel Steel Material No. !4 !5 !6 !7 !8 !