Series LX Construction and Mounting T-slots l Model Bolt Max. tightening torque Nm Max. screw-in depth (l mm) LXP M5 x 0.8 7.4 8.5 Use bolts at least 0.5mm shorter than the maximum screw-in depth, so they do not touch the body.
Do not use the drain tube in an upward direction. Do not bend or crush the drain tube. (The auto drain will not be activated and water will try to escape via the air outlet.) If it is necessary that the tube goes upwards, make sure it only goes as far as the position of the auto drain.
Do not lift the product by holding the panel, fittings or piping. Never lay the product down for transportation. This may lead to damage to the product. A polyurethane tube is attached as a drain tube for this product. Use this tube to discharge drainage to a drain tank etc. Do not use the drain tube in an upward direction. Do not bend or crush the drain tube.
D and DO type DC specifications are 24VDC or 12VDC only. D and DO type are for SY5000/7000 only.
Assembly / Disassembly procedure 12 4.1 With vertical auto switch unit 12 Size 10, 15 12 Size 20, 30 13 Size 40 14 4.2 With angle adjustment unit 15 4.3 With vertical auto switch unit and angle adjustment unit 16 Size 10, 15 16 Size 20, 30 17 Size 40 18 5.
3 MHY2-25D2 Opening/closing direction through hole type 4-5.5 (Hole for mounting attachment) 12 0.005 0.025 6 12 22.5 (Limted area for mounting attachment) Do not extend the attachment from limited area for mounting to avoid interference with the attachment or main body. 2.8-14 180 Angular Gripper Series MHY2 Setting Method of Auto Switch Projection of Auto Switch from Body Edge The projection
1l'" Immj 32 -700 50 7 5 10 64 72 32 36 79 90 25 31 ", 40 -800 55 9 7 10 Cushi()(\ vl\lve Port 4 50 -1000 70 9 12 12 90 45 50 110 120 36,S 39.5 63 1000 80 9 12 12 100 80 1000 100 12 14 16 126 63 153 45.5 J()a, -1000 120 14 1 6 I. 150 75 176 54 FE FT Head Iionge/ (G) Head flange 101m) ' ~," BoreSiW .
IC circuit A96V A96 5 V Reed switch Yes Yes Grommet 100 V 24 V 12 V A93 M9N M9P M9B F9NW F9PW F9BW F9BA A93V M9NV M9PV M9BV F9NWV F9PWV F9BWV 2-wire Relay, PLC 3-wire (NPN) IC circuit 5 V,12 V 2-wire 3-wire (PNP) 12 V Solid state switch Relay, PLC Grommet 5 V,12 V 24 V 3-wire (NPN) 3-wire (PNP) IC circuit Diagnostic indication (2-color indication) 2-wire 12 V Water resistant (2-color
Refer to Theoretical Output Table on page 8-29-12.
(Put packing B w on the surface contacting to the end plate.) (11 stations) 4 stations (12 stations) 5 stations 3. For a style with a D-sub connector, open the cover !4 and insert the pin of lead wire assembly !0 as shown in the right figure.
Name Material Number VVQ0-80A-4-2 Note) Packing NBR 12 A set of parts containing 12 pcs. each is enclosed. i
DO Without air cushion (mm) B Bore size (mm) No.
Do not use the product where these are present.
Actuator drive When an actuator, such as a cylinder, is to be driven using a valve, take appropriate measures (cover 12.Do not disassemble the product of installation or approach prohibition) to prevent potential danger caused by actuator operation. make any modifications, including additional machining. 3.
Regulator and filter regulator 1) Be sure to unlock the handle before adjusting the pressure and to lock it after the pressure is set. 2) During transport and installation, do not apply shock to the product, such as by dropping doing so will affect its precision. 3) Do not install it iin an area that is exposed to high temperature or humidity, because doing so will lead to improper operation
Connection thread size Proper tightening torque ( Nm) 1/8 7 to 9 1/4 12 to 14 -4- 3. Maintenance and Checks 3. Maintenance and Checks Caution a. Do not remove the parts and piping when the Service Parts product is pressurized. Always confirm that there is no residual pressure present before removal of unit.
V 12 V IC circuit 5 V, 12 V Relay, PLC Diagnostic indication (2-color indicator) Yes Grommet 24 V 12 V IC circuit 5 V, 12 V Water resistant (2-color indicator) M9PAV1 M9PA1 M9BAV1 M9BA1 12 V 3-wire (NPN equivalent) Grommet 24 V A96V A96 IC circuit 5 V Yes A93V2 A93 A90 IC circuit 100 V Relay, PLC 2-wire 12 V A90V No 100 V or less 1 Water resistant type auto switches can be mounted
Do not touch the leakage of fluid without care. If the fluid has high temperature or is chemical, the contact could result in burn and other injuries. 3) Disassembly Do not disassemble the pump. Caution 1) Quality of supplied air Mount the filter with filtration of approx. 0.01.
Do not use any other voltage as this may cause failure. Before mounting the sensor to the cylinder, stop the operation of the device to avoid injury. Do not use the product if there is smoke or a strange smell. Do not handle with wet hands. Avoid getting the product wet. In case of a malfunction, stop using immediately. This product is a piece of precision equipment.
Do not twist the valve seal 1.