Series HAW Water Cooled Aftercooler 1 Note 2) The accessories should be mounted by user.
Temperature Data A or B = Series IDUS: Data A Series IDFS: Data B Air pressure Data C = 3 2 Calculate corrected air flow by using A or B and C.
CA2Y100-PS Accessory When only grease for maintenance is necessary, please order by the following part numbers.
If one side of the piston is pressurized by supplying air with the clamp arm attached, the piston will move vertically while the clamp arm rotates. This operation could be hazardous to personnel, as their hands or feet could get caught by the clamp arm, or could lead to equipment damage.
How to Rotate the Relief Valve Body (20, 25, 32, 40) Caution The relief adjusting screw can be placed in any direction by rotating the relief valve body by following the steps given below. Procedure 1. Verify that there is no residual pressure in the cylinder. Then, loosen the mounting bracket (such as foot, flange, etc.). 2.
C85 Air cylinder Compact and light design C95 CP95 Die-casting of the covers has reduced the weight by 25%.
CU Length is shortened by approx. 64% max. Volume is reduced by approx. 70% max.
The load kinetic energy can be obtained by the following equation: 5 a 1 Rush speed into cushion (mm/s) 100 50 200 500 750 M Also, selection can be made by using the graph above. Example) Find the maximum load weight when using a cylinder with 32, stroke 500 mm, with rear plate as a lifter at an average speed of a 300 mm/s.
by the 1 stroke interval 40 to 100 Stroke available by the 5 stroke interval (Example) 1.
The lock ring is tilted by the spring force. 2. The tilting is increased by the load and the piston rod is securely locked. Unlocking port: Air supplied 1.
Sum of guide load factors = Load weight [m] Static moment [M] Note 1) Dynamic moment [ME] Note 2) 1 + + Maximum allowable load [mmax] Allowable static moment [Mmax] Allowable dynamic moment [MEmax] Note 1) Moment caused by the load, etc., with cylinder in resting condition. Note 2) Moment caused by the impact load equivalent at the stroke end (at the time of impact with stopper).
Static moment [M] (1) Dynamic moment [ME] (2) Sum of guide load factors = Load weight [m] + + 1 Allowable static moment [Mmax] Allowable dynamic moment [MEmax] Maximum load weight [m max] Note 1) Moment caused by the load, etc., with cylinder in resting condition. Note 2) Moment caused by the impact load equivalent at the stroke end (at the time of impact with stopper).
Note6) When the responsiveness is regarded as important, prevent negative fluctuation of the voltage by adequate regulation. Note7) The value is based on SMCs measurement conditions. The noise level will vary with conditions.
It then acts on diaphragm B as nozzle back pressure, the main valve is pushed down by the generated force, and the supply pressure flows out to the downstream side. The air pressure that flows in acts on diaphragm C. While opposing the force generated by diaphragm B it also acts on diaphragm A, opposing the compression force of the setting spring and becomes the set pressure.
To the fullest extent permitted by law, in no event shall SMC be responsible or liable for any incidental, consequential, or other damages, claims or costs arising from any product defect.
This lowers the pressure in the diaphragm chamber q and the force generated by the pressure regulator spring e pushes down the diaphragm.
This lowers the pressure in the diaphragm chamber q and the force generated by the pressure regulator spring e pushes down the diaphragm.
Press the button once to increase by one digit, or press it continuously to keep increasing the set value. Press the button once to decrease by one digit, or press it continuously to keep decreasing the set value. Panel mounting Fix the panel mount adapter to the product with the mounting screws (nominal size: 3 x 8 L, 2 pcs.) supplied.
Please confirm it to our company when you maintain the grease up etc.. 2 Recommended tube diameter Table2Recommended tube diameter An enough fluence is not obtained by a diameter that is thinner than this. Moreover, please enlarge it by one size when the piping length exceeds 3m.
Please confirm it to our company when you maintain the grease up etc. 1.2 Recommended tube diameter Recommended tube diameter Type Tube diameter(mm) 40,63 8 or more * An enough fluence is not obtained by a diameter that is thinner than this. Moreover, please enlarge it by one size when the piping length exceeds 3m.