0.4 Continuous operation possible. 50 L/min 80 W type Switching frequency: 1200 Hz The manifold base should be prepared by users.
The mist generating pressure differential setting is performed by adjusting the adjustment screw. The pressure differential (the difference between the boost pressure and the line pressure) is increased by turning the adjustment screw clolckwise, and decreased by turning counterclockwise.
Switch output is enabled by setting the upper and lower limits of pressure.
It then acts on diaphragm B as nozzle back pressure, the main valve is pushed down by the generated force, and the supply pressure flows out to the downstream side. The air pressure that flows in acts on diaphragm C. While opposing the force generated by diaphragm B it also acts on diaphragm A, opposing the compression force of the setting spring and becomes the set pressure.
rectifying circuit (AC) AC/DC switchover is possible by simply changing the coil.
1/3 by reducing the wattage required to hold the valve in an energized state.
Turn the manual override clockwise by 180 to set the E mark to "1" and press it in the direction indicated by arrow, then it will be locked in the ON state. Turn the manual override counterclockwise by 180 to set the E mark to "0", then it will be reset. Connection of Lead Wire (Not necessary if ordering pre-connected model.)
When part numbers written collectively are complicated, specify by using a manifold specification form.
Needle valve on the maniicld block can control c\,/linder speed by throttling exhaust. @ Part No.
Note 2) Intermediate stroke is available by the 1 mm interval. Note 3) Please contact SMC if the maximum manufacturable stroke is exceeded.
Bushing (Bearing) fR Reference: Even under a light load, if the piston rod has been stopped by an external stopper at the extending side of the cylinder, the maximum force generated by the cylinder will act upon the cylinder itself.
. :1, lJ lo: l0.2kgfcm ~ 20 a With air CUShion High ktnetic energy generated by a large lOad and high speed operatIOn can be absorbed by compressing air at the stroke end thus prevenllJl9 shock and VIbration beng transmitted Ie the machne. The atr cushion has nOI been designed 10 control Ihe piston speed in the end regions ot the $!
The transfer work over the recommended work load may cause the vacuum pressure to decrease by the air leak. The work load shown above is the value when the vacuum pressure reaches 85 kPa, and that is calculated by multiplying the theoretical value by a safety factor of 1/4 for the horizontal lifting or 1/8 for the vertical lifting.
These instructions indicate the level of potential hazard by labels of "Caution", "Warning" or "Danger". To ensure safety, be sure to observe ISO 4414 Note 1), JIS B 8370 Note 2) and other safety practices. Caution : Operator error could result in injury or equipment damage.
Bushing (Bearing) fR Reference: Even under a light load, if the piston rod has been stopped by an external stopper at the extending side of the cylinder, the maximum force generated by the cylinder will act upon the cylinder itself.
1 Plate Cylinder Series MU 25, 32, 40, 50, 63 By adopting an elliptical piston design, a slim, square shaped body has been achieved, resulting in a space-saving cylinder with unrestricted mounting directions.
When rotating the turntable, take care that hands or fingers are not caught by the position detector auto switch bracket. Because there is a danger of hands or fingers getting caught between the switch bracket and one of the magnet arms, please use caution when the turntable is being rotated. (By-pass port dia.)
If two or more cylinders are used in close proximity, the auto switches may malfunction affected by the magnets built in the nearby cylinder. Please keep the cylinder mounting pitch larger than the values in the table below.
Return to origin using IN0: Return to origin by moving to the extended end. Return to origin using IN1: Return to origin by moving to the motor end. Not output when alarm is active or servo OFF Note) Signal of negative-logic circuit (N.C.)
Moment resistance*1 *2 Table displacement*1 61% Improved by up to 50% Reduced by up to With internal battery-less absolute encoder Restart from the last stop position is possible after recovery of the power supply.