Controller setting Software (ACT Controller) Easy mode 9 4.1 Summary of Easy mode 9 4.2 Menu 12 4.3 Teaching method 13 4.3.1 Preparation 13 4.3.2 Jog teaching 13 4.3.3 Direct teaching 13 4.4 Test drive method 14 4.5 Pitch transfer method 14 4.6 Jog transfer method 15 4.7 Alarm 15 5.
If the product is operated at a pressure lower than the minimum operating pressure, it may cause deterioration in the performance or malfunction. 4 - Installation Warning 1) Do not drop or apply impact during transportation or installation. It will cause damage to the product and result in operation failure. 2) Do not install in areas of high humidity or high temperature.
) Note 12) Note 12) i ZA Note 11) Pressure unit Name plate, caution plate for bowl, and pressure gauge in imperial units (PSI, F) Digital pressure switch: With unit switching function Note 13) Note 13) Note 13) Note 10) For thread type: NPT.
) Note 12) Note 12) i ZA Note 11) Pressure unit Name plate, caution plate for bowl, and pressure gauge in imperial units (PSI, F) Digital pressure switch: With unit switching function Note 13) Note 13) Note 13) Note 10) For thread type: NPT.
Max. 11 mm shorter 11 mm shorter With adapter Pad unit Actual size Actual size 19.5 mm 12 mm 8.5 mm 3 mm ZP3 ZP3 ZP (Existing model) ZP (Existing model) Space saving 2 piping reduces working space!
Do not use these for pneumatic operations because they will lead to oil leaks. Air-hydro cylinder: CA1HCQ2HCS1HCM2HCG1H(up to 63) HC03-X1x Air-hydro rotary actuator: CRA1H2.
OUT1 OUT2 GND 12 to 24 VDC OUT1 OUT2 GND 12 to 24 VDC List of output mode Auto shift Error Caution
Do not twist the valve seal 1.
Do not use lead wire retainers for unclamp angles of 105 , 120 and 135 . Failure example 1 There should be no slack in the lead wire. Lead wire retainers Failure example 2 Do not use the lead wire retainer above the switch. Lead wire Close the cover until you hear a click, and put the excess lead wire in the lead wire storage space.
Do not operate in locations having an atmosphere of corrosive gases, chemicals, sea water, water or steam, or where there will be contact with the same. 2. Do not operate in locations where vibration or impact occurs. 3. In locations which receive direct sunlight, provide a protective cover, etc. 4. In locations near heat sources, block off any radiated heat. 5.
Do not use at temperatures (fluid or ambient temperatures) higher than the prescribed operating conditions.
Yellow flashing Bus IN side: Link, Activity(10 Mbps) 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. OFF. Parameter Setting Hardware Configuration I/O Map Diagnostic Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not apply excessive force or impact. This will not only damage the product but also decrease its performance and life expectancy. It is not possible to disassemble the bonnet assembly of this product. If the components and assembly are damaged, or damage is expected, exchange the bonnet assembly itself. Do not disassemble the parts that are not explained in this operation manual.
Do not apply excessive force or impact. This will not only damage the product but also decrease its performance and life expectancy. It is not possible to disassemble the bonnet assembly of this product. If the components and assembly are damaged, or damage is expected, exchange the bonnet assembly itself. Do not disassemble the parts that are not explained in this operation manual.
For AC specifications, Nil is only set for electrical entry DO. Right Left Right Left IN IN Options (For details, refer to page 12.)
BUS 3 3 X X B B 12 12 Technical documentation giving detailed diagnosis information and set-up steps information can be found on the SMC website (URL http://www.smcworld.com). PWR P P 1 1 A A Terminating resistors It is necessary to attach bus terminating resistance to the units located at the ends of transmission line.
Do not use the back pressure regulator as shutoff valve or safety valve. 2.