PSxx-OMQ0004E F 0 Unit selection 1 [ PA] kPa Connector Switch point Hysteresis Display colour ISA3-F: [ 20], ISA3-G: [ 50], ISA3-H: [ 50] OUT1 setting Bracket mounting hole ISA3-F: [ 3], ISA3-G: [ 20], ISA3-H: [ 20] F 1 [ SoG] Green when ON, Orange when OFF out2: [ Ewin] OUT port side pressure detection window comparator mode Output mode Thank you for purchasing an SMC ISA3 series Gap Checker.
Do not use in an atmosphere containing corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. Warning 2. Lubrication amount 2. Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction.
So, do not apply a large amount of oil. Operating Environment 1. Do not use in an atmosphere containing corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. Air Supply 1. Type of fluids 2. Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion.
Do not use in an atmosphere containing corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. Warning Air Supply 2. Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction. 1.
Please consult with SMC for details. (1) Do not use in an environment where corrosive gases, chemicals, sea water, water or steam are present. (2) Do not use in explosive atmospheres. (3) Do not use in locations subject to vibration or impact. (4) Do not use in areas where product is exposed to heat sources or in areas where the product is exposed to radiant heat. (5) Employ suitable protective
Do not use in atmospheres contacting corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not use in explosive atmosphere. 3. Do not use in locations subject to vibration or impact. 4. Do not expose to direct sunlight for an extended period of time. Protective cover should be used to shield. 5.
Do not use in atmospheres contacting corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not use in explosive atmosphere. 3. Do not use in locations subject to vibration or impact. 4. Do not expose to direct sunlight for an extended period of time. Protective cover should be used to shield. 5.
Do not remove any name plate or label. Do not drop, hit or apply an excessive shock to the unit. Follow the specified tightening torque. Do not apply any excessive force to cables by repeated bending, tensioning or placing a heavy object on the cables. Connect wires and cables correctly. Do not perform any wiring work while the power is on.
Do not drop, bump, or apply excessive impacts (980 m/s2) while handling. Although the body of the sensor may not be damaged, the inside of the sensor could be damaged and lead to a malfunction. 2. The tensile strength of the cord is 20 N. Applying a greater pulling force on it can cause a malfunction. When handling, hold the body of the sensor do not dangle it from the cord. 3.
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.
Do not bend piping less than the minimum bending radius. If it is installed on the inlet side, dehumidification performance will be reduced. 6. Do not use the product for applications that requires bending and stretching repeatedly. Minimum bending radius of tubes is 35mm and bending angle is 90 degrees or less. Do not bend the part of 50mm from the nut end. Also do not twist. 7.
Do not use valves where there is direct contact with, or in atmospheres of, corrosive gases, chemicals, salt water, water or steam. 2. Do not use in an explosive atmosphere. 3. Do not use in locations subject to vibration or impact. Confirm the specifications for each series. 4. A protective cover should be used to shield valves from direct sunlight. 5.
Do not use in locations having an explosive atmosphere. 2. When vibration or impact is applied, make sure to test in the 2.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
If you do not agree to the following disclaimer, you may not use or copy this software. "Disclaimer" 1.
Do not use the membrane dryer in an environment containing these chemicals substances.
Refer to P24 the dimensional drawings for necessary space. (3) Do not drop or apply impact during transportation or installation. Damage of products or pressure gauge can result in malfunction. (4) Do not install in areas with high humidity or high temperature.
40 60 80 100 120 140 0 10 20 30 40 50 60 70 80 90 100 Flow rate l/min (ANR) Flow rate l/min (ANR) SRP1-01 SRP1101-01 Conditions/Upstream pressure: 0.5MPa Conditions/Upstream pressure: 0.7MPa 0.25 0.50 0.20 0.40 Downstream pressure MPa Downstream pressure MPa 0.15 0.30 0.10 0.20 0.05 0.10 0.00 0.00 0 20 40 60 80 100 120 140 160 180 200 0 20 40 60 80 100 120 140 Flow rate l/min (ANR) Flow
40 60 80 100 120 140 0 10 20 30 40 50 60 70 80 90 100 Flow rate l/min (ANR) Flow rate l/min (ANR) SRP1-01 SRP1101-01 Conditions/Upstream pressure: 0.5MPa Conditions/Upstream pressure: 0.7MPa 0.25 0.50 0.20 0.40 Downstream pressure MPa Downstream pressure MPa 0.15 0.30 0.10 0.20 0.05 0.10 0.00 0.00 0 20 40 60 80 100 120 140 160 180 200 0 20 40 60 80 100 120 140 Flow rate l/min (ANR) Flow
When mounting the load with screws, do not exceed the maximum tightening torque. (The torque may vary depending on the material of the load.) Bolt Model Maximum tightening torque (Nm) Caution MGJ6 M2.5 x 0.45 0.5 MGJ10 M3 x 0.5 1.0 1. Do not scratch or dent the sliding parts of the piston rod and guide rods. Damage to seals can cause air leakage or malfunction, etc. 2.