CYL, E, A, 50, TN, S, R, M16X1.5 THREAD. 2.87600 lb. 341.
CYL,D,B,A,50,FEMALE THD, ROD EXT. 1.97200 lb. E18.
CG5 mounting brackets , Type: flange, foot, trunnion bracket , Applicable to all bore sizes, CYL, D, B, A, 50, TN, V, X165US, Thread, WATER RESISTANT CYLINDER, 341, 2.39700 lb
Please contact us for the latest version.sales@ocaire.com, CYL, W/LOCK, A/CUSH, A-SW, ACTUATOR, CNG CYLINDER W/LOCK, LE, 32MM CNG DBL ACTING, AUTO-SW, .00000 lb
No response is returned when a request message is sent from a slave address other than those set in the product. 5.1.2 Precautions for communicating 1) Allow a suitable interval between requests. To send request messages in series, wait for 50 msec. or longer after receiving a response message from the product before sending the next message. 2) Retry (resend request message).
Plugging one of the cylinder ports (A or B) enables use as a 3 port valve. lt should not be used in special applications such as use as a non-leakage valve. Make sure the exhaust port is open if used as a 3 port valve. Solenoid {X) represents plugged port. common Exhaust ifflg"o,BJ"". rnd Pilot valve I Exhaust air from pilot valve will flow to main valve exhaust port.
location where it will be used as a support.
VR VH VHS Pilot port (A side) 2-M5 x 0.8 sub-plate side (P , A, B port) (R1, R2 port) 2 position double: VZA4241--01 02 Pilot port (B side) Body side Pilot port (A side) 2-M5 x 0.8 body side 2-4.5 Mounting hole Pilot port (A side) 2-M5 x 0.8 sub-plate side (R1, R2 port) (P , A, B port) Pilot port (B side) Sub-plate side 5-3-7 8 Series VZA4000 Dimensions: Base Mounted 3 position closed center
The additional air blow can be set to continuous or pulse (50/100 ms intervals). Ionizer Additional air blow Air blow Ionized air 497 ZVB Series Dimensions C B D A C B A D F E [ZVB20] F E [ZVB40] Model A B C D D Note 1) E F F Note 2) ZVB20 211 202 212 310 351 210 297 341 ZVB40 248 392 298 349 390 400 384 428 Note 1) Dimension D is the overall height including the knob of the regulator.
Upper 3 digits Lower 3 digits Reverse output Warning: + ON Time Part A should then be pressed in using a suitable tool, such as pliers. 2 sec. OFF Initialize mode DANGER indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
LVP Different Diameter Tubing Applicable with Reducer LVW Specific Product Precautions Different diameter tubing can be selected (within a body class) by using a nut and insert bushing (reducer). Applicable fitting: LQ2 Be sure to read this before handling the products. Refer to back page 50 for Safety Instructions. LQ1 LQ3 Tubing O.D.
Seal kit includes a grease pack (20 to 50: 10 g, 63, 80: 20 g). Order with the following part number when only the grease pack is needed.
Auto Switch Proper Mounting Position (Detection at stroke end) and Its Mounting Height Auto switch (Sensor section) 16 to 25 Indicator light A 17.5 B [mm] Auto switch model Bore size D-M9 J A B U 16 9.5 7 21 20 9.5 8.5 23.5 25 9.5 9 27 32 11 8 29 40 15 10.5 31 50 13 13.5 36 63 15.5 16.5 41.5 22 U 64.5 4 Auto switch (Amplifier section) 32 to 63 A 17.5 B U Note) Adjust the auto switch after
Part No. of Cylinder with Built-in Magnet Mounting Symbol "-A" (rail mounting) or "-B" (band mounting) should be suffixed to the part No. of the cylinder with auto switch. B L F D Basic Axial foot Front flange Double clevis Note) Lock position H R Rear end lock Front end lock Rail mounting CDBJ2B16-45-A Note) Front end lock only. Ex.
Danger: DANGER indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. SET button Press this button to change the mode and to set a value.
Turn cover A counterclockwise until it stops (approx. 45). 4. Install a new element on cover A and insert it into the case. Cover A Case Cover A Case O L L Element O-ring Window 5.
SealKir 25, 30, 35, 40. 45, 50, 75, 100 25 30,35,4A, 45,50.75, tOD 25, 30, 35.40, 45, 50, 75, 100 .Ho{ to make interrediaie slroke rtrmediale stroke berwen 50-l0o (5s,60,65 ...) are obtained throlgh the use ol spaceB (5. 10, 1s,20mm) (Example) CDQBPSo-55 oMr S[4C would install a 20mrn width spacer in rire cDQ2Bp 50 750M. ll lool brackel is required, order 2 pcs/cylindef.
Load is an analog input equipment such as a voltmeter.
However, this is just a guide. For precise setting use a flow meter. 1 2 3 4 5 6 7 8 9 10 11 12 Flow adjusting screw (Rotations) 0 Contact ON-flow (%) 30 40 50 59 68 74 80 85 89 93 96 98 100 3. The flow rate setting point is set at the ON-flow rate. Therefore, in case of 1a contact, ON signal is output when the fluid with higher flow than the setting flow rate is flown.
Note 3) in part numbers for a round pressure gauge indicates a pipe thread type. No indication is necessary for R; however, indicate N for NPT. Please contact SMC regarding the pressure gauge supply for both MPa and psi unit specifications. Note 4) in part numbers for a round pressure gauge indicates a type of connection thread.