Conforming to ISO Standard Solenoid Valve (with M12 Connector) Series EVS7-6/7-8/7-10 (Size 1) (Size 2) (Size 3) 1 Note 2) Impact resistance: No malfunction resulted during an impact test using a drop impact tester. The test was performed one time each in the axial and right angle directions of the main valve and armature for both energized and de-energized conditions. Vibration resistance: No malfunction resulted during an one-sweep test between 8.3 and 2000 Hz.
This may also have an adverse effect on the peripheral equipment in proximity. Should a valve be continuously energized for long periods, or its daily energized state exceeds its non energized state, please use an energy saving type AC, energizing for long periods of time continuously, select the air-operated valve and use the continuous duty type of the VT307 for a pilot valve.
Because suctioned matter is ejected together with exhaust, do not direct an exhaust port at a person or equipment. AFJ AMV 2.
(This is to prevent the setting from remaining incomplete if, for instance, an operator were to leave during setting) : 3 step setting mode and Function selection mode are reflected on each other. 1 2 [ 50] 50 L/min (PFMB7102) [ 100] 100 L/min (PFMB7202) System error An internal data error has occurred. Turn the power OFF and turn it ON again.
NPT ZQ 06 3/4 10 1 ZF ZP Nil 2 6 J R Option/Combinations Combination available Combination not available ZCU Option Symbol Drain cock Nil AMJ Metal bow 2 Nylon bowl Misc. 6 Drain guide J Flow: Right Left R Model Model AMJ5000 AMJ4000 AMJ3000 Recommended flow rate (l/min(ANR)) 500 300 200 Port size (Nominal size B) 3/4, 1 3/8, 1/2 1/4, 3/8 Weight (kg) 1.1 0.6 0.3 Specifications Fluid Air
UJ I 2-Forled \bBion DIMENSIONS A B c o E F G H J K M P R s T 1.57 (40) 2.52 (64) 2.20 (56) 1.77 (45) 4.80 (1221 1.97 {50} 0.98 (25) 1 . 1 0 (28) 0.51 (13) 4.45 (113) ?
UJ I 2-Forled \bBion DIMENSIONS A B c o E F G H J K M P R s T 1.57 (40) 2.52 (64) 2.20 (56) 1.77 (45) 4.80 (1221 1.97 {50} 0.98 (25) 1 . 1 0 (28) 0.51 (13) 4.45 (113) ?
Applicable cable O.D. 6 to 8 Light/surge voltage suppressor (For DZ) Manual override (Non-locking push type) E Pilot port 12(P1), 10(P2) Port size: refer to table below C K (External pilot solenoid) P1 P2 J J B (Air operated) D 4 x 2 x 18 mouting hole 32 H F A Applicable flange Port 1, 2 Pilot port 12(P1), 10(P2) A Model B C D E F H J K Note) VNC5-32F VNC6-40F VNC7-50F 1 8 1 4 1 4 32 40
Brake 400W without brake Symbol G *Standard strokes are available in 50 mm increments. 400W with brake H 400W without brake J Matsushita Electric Industrial Co., LTD 400W with brake K Caution When X, Y and Z axes are combined, Y axis attachment bracket is supplied as standard.
Before using an SMC fitting and S coupler, please refer to "Tightening the threaded portion of the connection thread" of the Fittings & Tubing Precautions. Maintenance 3. Piping materials without flexibility such as steel tube piping, are prone to be effected by excess moment load and vibration from the piping side. Use flexible tubing in between to avoid such an effect. Warning 1.
E l e c t r i c a l c a b l e m u s t n o t b e s u b j e c t e d t o excessive force. 2 When connecting the switch, use a spanner on the h e x a g o n f i t t i n g . N E V E R u s e t o o l s o n t h e s w i t c h body. 3 Do not use switch near corrosive materials. 4 The switch is not liquid sealed.
oil odor. 3) Use the length of time calculated in step 2) as an approximate effective deodorization time.
D-864 Bone Sizes Rod Boot o75 -%', 088 -',6' 106 -1%6" 125 -114" 't50 -1%' J -Nylon K -Neoprene Astuation -Double Acting S -Spring Return T -Spring Extend srror,.rrn"r, Sirokg/Hundrlh ol an lnch Cushion' C -Rubber Bumper Note: Min. Strokes for Auto Switch Cylinders page 5. *Rubber Bumpers are no additional cost on 7s" & 174" bore size cylinderg. Thy are options on the other bore sizes.
Note 2) Through-hole in case of 5 mm stroke. 754 CQS 2122CQS/ 1011Compact Cylinder Mounting Bolt for CQS Mounting method: Mounting bolt for through-hole mounting of the CQSB is available as an option. Refer to the following for ordering procedures. Order the actual number of bolts that will be used. Example) CQ-M3 x 35L 2 pcs.
Cushion adjustment is not necessary because the model can perform smooth acceleration and deceleration in a wide range of strokes without an adjusting cushion. RHC MTS Relieving port CC In general specifications, relieving port is blocked with a hexagon socket set screw. This screw should not be removed, because dust may enter inside through the relieving port.
The projection of an auto switch from the edge of the body is shown in the table below. Use the table as a guideline for mounting. Note) 2-color indicator type and perpendicular entry type protrude in the direction of the lead wire entry.
(If an SSC valve is used on both sides, perform the adjustment at the cylinder speed adjustment set needles on both sides.) After adjusting, tighten the lock nut. Keep the cylinder cushion needle on the side with the SSC valve as open as possible. 4.
The projection of an auto switch from the edge of the body is shown in the table below. Use the table as a guideline for mounting. Note) 2-color indicator type and perpendicular entry type protrude in the direction of the lead wire entry.
Select a fitting with an I.D. greater than 8 for the VP344 and the VP342; more than 10 for the VP544 and VP542, and more than 12 for VP744 and VP742 when piping length is less than 3 meters. Use an external pilot when there is a small flow outlet of the valve.
Further, give nut an additional 1 turns with appropriate wrench or the like.Leave 0 space between the screwed-in nut and the tube in-line with the tube axis. If tightened insufficiently, nut may be loosened and it may cause the air leakage or tube coming off. When using soft copper tube, first tighten the nut by hand and then give it an additional one turn with wrench.