OR connection / / + + In case of AND connection of two 2-wire type switches, load malfunction may be caused by the load voltage decrease when turned ON. The indicator light comes on when the two switches are turned ON. In case of OR connection of two 2-wire types switches, load malfunction may be caused by the load voltage increase when turned OFF.
the cylinder and the energy generated by the external force within the values that are shown in the bottom chart.
Socket Plug case Socket case Hold surely by inserting the both of tube and barb. Possible connect in the required position by the convex and concave for engagement. Plug Easy insertion of tube by the floating mechanism to adjust to the case hole. Cover Socket side Plug side Stopper (With expander) One-touch installation and removal.
Refrigerated Air Dryer Refrigerated Air Dryer Refrigerated Air Dryer Air Flow Capacity Power Consumption Air Flow Capacity Power Consumption Increased by up to 40% Increased by up to 40% Reduced by up to 40% Reduced by up to 40% Increased by up to 40% Reduced by up to 40% (Compared with the previous model) (Compared with the previous model) 40 40 MAX. 40% 40 40 MAX. 40% Improved corrosion
Cable lengths other than those shown below should be arranged by the customer.
P/A warrants that for 18 months or 1800 service miles*, whichever occurs first from date of purchase, it will replace or make adjustment at P/As option, of any defective cylinder sold if the cylinder product is returned with P/As prior written consent, transportation prepaid by the original buyer, and received by P/A at its place of business within the warranty period.
Just by removing the snap ring and collar, seal replacement is possible. Collar Snap ring Super Compact type is available saves additional space.
The dried clean air is heated by the hot air that has entered the dryer. It is then discharged from air dryer outlet.
Energy saving in pneumatic system Considering electric power consumption classified by the purpose of use, it is reported that the electric power used for air (compressors) accounts for 20% of the total consumption (Figure 1 ). Figure 2 shows air consumption classified by the purpose of use.
Large flow rate: Cv factor 0.16 to 2.1 Smaller size: Single valve 15% reduction in volume (Class 2) Manifold length Reduced by 18% (Class 3 : 7 stations) (P/A comparison) Clip type Internal surge voltage suppressor Quick change coils Clip design makes coil replacement easy Internal rectifier circuit (AC) AC/DC switchover is possible by simply changing the coil Reduced noise Incombustibility
Note) Manifold bases are composed by connecting 2 station and 3 station bases.
Also, even within the warranty period, the wear of a product due to the use of the vacuum pad or failure due to the deterioration of rubber material are not covered by the limited warranty.
Also, even within the warranty period, the wear of a product due to the use of the vacuum pad or failure due to the deterioration of rubber material are not covered by the limited warranty.
Article 6 (Rights of this Software) The copyright and any other rights of this Software are owned by SMC, and protected by Japanese copyright laws and international treaty provisions. Article 7 (Governing law and jurisdiction) 1. This Agreement shall be governed by Japanese law. 2.
All solenoid valve outputs are reset to zero. 2 SV0 V 0 V for valve 3 SW24 V +24 V for input 1 4 5 SW0 V 0 V for input 4 Mode setting 5 FE Ground URL https://www.smcworld.com Mode SW1-10 0 H / W mode Set address and communication speed by SW1 to 8.
Connect End Plate and tighten removed screws by specified tightening torque. (0.6 Nm) H L Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. DIA Red lights up when some failure is detected by self-diagnosis.
However, drain can be discharged by manual operation if needed. In this case, it can be discharged by loosening the knob on the auto drain port until it points to “O” (OPEN). (Remember to return the knob to “S” (SHUT) by tightening it after discharge.)
Do not pull the cable out by holding the cable. 4. Note the key direction. Especially for the SPEEDCON specification, match the protrusion of the knurl (bracket) and the mark at the mold for insertion so that the SPEEDCON function can be maintained. 5.
position pressure center 2 position single 2 position single (B) 2 (B) 2 (A) 4 (A) 4 1 (P) 3 (R) 5 (R) 1 (P) 3 (R) How to Order Manifold Base 2 position double 2 position double (B) 2 (A) 4 (B) 2 (A) 4 Same manifolds as series SYJ3000 are prepared. 1 (P) 3 (R) 5 (R) 1 (P) 3 (R) SS5YJA3 Fill the same as SS5YJ3 3 position closed center 3 position closed center (B) 2 (A) 4 (B) 2 (A) 4 Instruct by
When this is the case, decrease the supply pressure as much as possible or slightly increase the set pressure and restrict the output line (such as by adding a throttle valve to adjust the pressure). Can also be used in an intensive piping system.