Magnet Gripper If the fluid temperature is 5C or less, the moisture in the circuit could freeze, causing damage to the seals or equipment malfunction. Therefore, take appropriate measures to prevent freezing. For compressed air quality, refer to the SMC Best Pneumatics No. 6 catalog. 5.
If the fluid temperature is 5C or less, the moisture in the circuit could freeze, causing damage to the seals or equipment malfunction. Therefore, take appropriate measures to prevent freezing. 5) Precautionary measures against condensation Moisture condensation can occur inside pneumatic systems due to a drop in temperatures caused by the piping or operating conditions.
Take measures to prevent freezing, since moisture in circuits will be frozen under 5C, and this may cause damage to seals and lead to malfunction. Lubrication to the low-friction type cylinder. Please do not lubricate this cylinder.
Take measures to prevent freezing, since moisture in circuits will be frozen under 5C, and this may cause damage to seals and lead to malfunction. Refer to SMCs Air Cleaning Equipment catalog for further details on compressed air quality. Piping Caution 1.
Use the product within the range of specifications for fluid and ambient temperature Take measures to prevent freezing when used at 5C or less, since moisture in circuits can freeze, causing malfunction. 2. Install air filters Install air filters near valves on their upstream side. The filtration degree should be 5 micron or less.
Take measures to prevent freezing, since moisture in circuits can be frozen under 5C, and this may cause damage to seals and lead to malfunction. Refer to SMCs Air Cleaning Equipment catalog for further details on compressed air quality. 4. Take measures to prevent pressure fluctuation.
At temperatures of 5C or lower, take measures to prevent freezing, since moisture in circuits may be frozen and this can cause damage to seals and lead to malfunction. Refer to SMC s "Best Pneumatics vol. 4" catalog for further details on compressed air quality. Operating Environment Warning 1. Do not use in environments where there is a danger of corrosion.
Note 3) Temperature conditions: at 20C (5C), in other cases, 6C F.S.
Use the product within the range of specifications for fluid and ambient temperature Take measures to prevent freezing when used at 5C or less, since moisture in circuits can freeze, causing malfunction. 2. Install air filters Install air filters near valves on their upstream side. The filtration degree should be 5 micron or less.
Mandrel Here, : Deformation ration (%) d: Tube diameter (mm) L: Measured length (mm) D: Mandrel diameter (mm) (Twice against the minimum bending radius) Handling of One-touch Fittings Test temperature: 20 5C Relative humidity: 65 5%. Caution 3. Applicable for general industry water. Please consult with SMC if using other fluids.
Ambient and fluid temperature operation is as follows: Digital pressure switches: 0 to 50C Other pressure switches: 0 to 60C Take measures to prevent moisture from freezing in circuits when below 5C, since this may cause damage to the O-ring and lead to a malfunction. The installation of an air dryer is recommended for eliminating condensate and moisture.
Ambient and fluid temperature operation is as follows: Digital pressure switches: 0 to 50C Take measures to prevent moisture from freezing in circuits when below 5C, since this may cause damage to the O-ring and lead to a malfunction. The installation of an air dryer is recommended for eliminating condensate and moisture.
Ambient and fluid temperature operation is as follows: Digital pressure switches: 0 to 50C Other pressure switches: 0 to 60C Take measures to prevent freezing moisture in circuits when below 5C, since this may cause damage to the O-ring and lead to a malfunction. The installation of an air dryer is recommended for eliminating condensate and moisture.
Take measures to prevent freezing, since moisture in circuits can be frozen under 5C, and this may cause damage to seals and lead to malfunction. Refer to SMCs Air Cleaning Equipment catalog for further details on compressed air quality. Maintenance Warning Also, when sealant tape is used, leave 1.5 to 2 thread ridges exposed at the end of the threads. 1.
Clean Exhaust Filter SFE Series RoHS How to Order SFE 11 Size/Port size Male thread type Plug-in type Symbol Port size Max. ow capacity L/min (ANR) 11 M5 x 0.8 3 42 R1/8 65 52 R1/8 130 53 R1/4 130 73 R1/4 200 Symbol Port size Max. ow capacity L/min (ANR) 3A 4 30 4B 6 65 5C 8 130 7D 10 200 Male thread type One-touch tting type Symbol Applicable tubing O.D.
Size/Port: 5C [Plug-in Type, Port Size: ø8, Flow: 130 L/min (ANR)]
Fitting Type: B (Branch Tee), Size Combination: 5C (Tubing: 3/4" x 5/8"; Thread: 3/4"), Piping Type: F (Female), Thread: R, Rc, Packaging: 1 (Packaging Equivalent to Class M5.5)
Fitting Type: B (Branch Tee), Size Combination: 5C (Tubing: 3/4" x 5/8"; Thread: 3/4"), Piping Type: M (Male)
Fitting Type: B (Branch Tee), Size Combination: 5C (Tubing: 3/4" x 5/8"; Thread: 3/4"), Piping Type: M (Male), Thread: N (NPT), Packaging: 1 (Packaging Equivalent to Class M5.5)