Process Valve This may also have an adverse effect on the peripheral equipment in proximity. Should a valve be continuously energized for long periods, or its daily energized state exceeds its non energized state, please use an energy saving type valve with DC specifications.
Holding point L (mm) 120 80 160 200 20 40 60 Holding point L (mm) 80 0 20 40 60 Holding point L (mm) 80 100 120 MHW2-25D MHW2-40D MHZ2 160 50 Pressure 0.7MPa Pressure 0.7MPa 140 MHZJ2 0.6 0.6 40 120 Holding force (N) Holding force (N) 0.5 0.5 MHQ 100 30 0.4 0.4 80 0.3 MHL2 0.3 20 60 0.2 0.2 40 10 MHR 20 0 20 40 60 Holding point L (mm) 100 80 20 40 60 Holding point L (mm) 80 100 120 140 160
Install an air filter. Install an air filter upstream near the valve. Select an air filter with a filtration size of 5 m or smaller. 3. Take measures to ensure air quality, such as by installing an aftercooler, air dryer, or water separator. Compressed air that contains a large amount of drainage can cause the malfunction of pneumatic equipment, such as air grippers.
Install an air filter. Install an air filter upstream near the valve. Select an air filter with a filtration size of 5 m or smaller. 3. Take measures to ensure air quality, such as by installing an aftercooler, air dryer, or water separator. Compressed air that contains a large amount of drainage can cause the malfunction of pneumatic equipment, such as air grippers.
s2 / 90 m/s2 P7, P10 (Quick fastener) C4, C6, C8, C10 (One-touch fitting) Port size Orifice diameter 1, 3, 4.5, 6 Rated voltage 24 VDC, 12 VDC 10% of rated voltage Allowable voltage fluctuation Coil insulation type Class B 500 VDC, 10 M or more Insulation resistance Voltage limit 1800 VAC, 1 sec., 3 mA or less Simulation noise: 500 Vp-p (Based on 1 sec. pulse width, 50 10 Hz frequency noise
20 20 20 20 20 20 20 9.5 9.5 9.5 11.5 D-F7, F7V D-J79, J79C D-F7W, F7WV D-J79W D-F7BAL, F7BAVL D-F7NTL, F79F D-F7W D-J79W D-F7BAL D-F79F D-F9BAL 6 6 6 6.5 Number of auto switch D-F7LF D-A9 D-F9 D-A79W 7.5 7.5 8 D-F7LF 7.5 D-F9, F9V D-F9W, F9WV D-F9BAL 1 pc. 2 pcs. 20 20 20 20 25 25 20 20 5.5 5.5 5.5 6.5 The operating ranges are provided as guidelines including hystereses and are not guaranteed
less 250 x 250 18 625 or less 282 Body size under 100 to 150 350 or less 300 x 300 20 900 or less 339 20 to 350 under 150 to 200 400 or less 23 Over 900 under 200 to 250 450 or less Order a thickness equal to or greater than that shown on the table.
Combination Spacer Select one of the spacers below when connecting to an F.R.L. combination unit (AC2000 to AC6000). (Spacers must be ordered separately.)
Install an air filter. Install an air filter upstream near the valve. Select an air filter with a filtration size of 5 m or smaller. 3. Take measures to ensure air quality, such as by installing an aftercooler, air dryer, or water separator. Compressed air that contains a large amount of drainage can cause the malfunction of pneumatic equipment, such as magnet grippers.
-Outside Local Area: (800) 258-9200-www.stevenengineering.com l 300 200 300 MGTL80 CX P = 0.5 MPa m 200 MGTM80 100 P = 0.5 MPa Load weight m(kg) Load weight m(kg) D40 50 100 Larger than 75st 50st 25st Larger than 50st 30 20 -X 50 40 25, 50st 10 30 205 4 3 2 20 Data 10 20 30 40 50 100 200 300 1 1 2 3 4 5 10 20 304050 100 200300400 Eccentric distance l (mm) 10 400 Eccentric distance l (mm)
Snap ring m 1.5 1.25 1.25 1.75 t 0.9 1.15 1.15 1.15 Part No.
Install an air filter. Install an air filter upstream near the valve. Select an air filter with a filtration size of 5 m or smaller. 3. Take measures to ensure air quality, such as by installing an aftercooler, air dryer, or water separator. Compressed air that contains a large amount of drainage can cause the malfunction of pneumatic equipment, such as air grippers.
HEC-OM-S008 First edition Aug.2014 Rev1.2 May.2017 C Co om mm mu un ni ic ca at ti io on n M Ma an nu ua al l THERMO-CON Model No. HECR series Keep available whenever necessary.
lead wire Option L, M plug connector is 220 VAC at the maximum.
Example) For setting the gripping force to be at least 20 times the work weight; Required gripping force = 0.05 kg x 20 x 9.8 m/s2 = 10 N min.
Example) For setting the gripping force to be at least 20 times the work weight; Required gripping force = 0.05 kg x 20 x 9.8 m/s2 = 10 N min.
Thread depth 6 2-M Thread depth 6 K VN LVC LVA LVH DIN terminal: D Conduit terminal: T LVD F F (Q) Q S 34 LVQ D LQ LVN U 25 R C 44 TI/ TIL C R G1/2 PA E E G1/2 PAX B B 2-P Port size A A D 2-P Port size (S) PB Port size G1/2 Compatible heavy-duty cord Cable O.D. 6 to 12 L L K 2-M Thread depth 6 K 2-M Thread depth 6 (mm) Electrical entry P Port size B Model A C D E F K L M Grommet: G Conduit
TECHNICAL CHARACTERISTICS 4.1 Technical Features of the Dryers Series PDE 3 20 -S 5.
M 4.Types of air. 2.Ensure space for maintenance.