PF2D Processing chart for Series PF2D Body Vibration reducing seals Malfunctions (output errors) that would otherwise be caused by vibration are prevented. Remote type sensor unit Sensor Assembly Common environment 4 types of outputs available With button operation, 4 types of output specification combinations are available.
OUT1 OUT2 z Presence of a workpiece is confirmed by detecting the back pressure at the nozzle. 16-1-9 7 Pressure Switch Application Example Low Differential Pressure Detection 1 3 Filter clogging monitoring 1 2 Flow control 16-3-33 16-3-33 Series PSE550 Series PSE550 Can control filtration and replacement periods by monitoring the clogging of the filter.
.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com Compact: Single valve volume reduced by 15% (Class 3) VX3 VXA Clip type VN Ease of maintenance has been improved. Changing of the coil is made easy by means of clip design.
Select ejectors with a suitable suction flow rate by referring to their technical data. 4. If the suction flow rate is too high, setting of vacuum switches will become difficult.
For standard installation, turn 15 to 30 using tool, after fastening by hand. Pay attention not to over torque the product.
Cylinder Mounting Bracket, by Stroke/Auto Switch Mounting Surfaces st: Stroke (mm) Auto switch model Basic, Foot, Flange, Clevis With 1 pc. (Rod cover side) With 2 pcs. (Different surfaces) With 2 pcs.
GTa disassemble, hold the spanner flats of the tube COver in a vice 40 20 9,43 37,7 47.2 56,6 IN 28,3 and by holding the rod cover spanner flats with a spanner, 98,2 OUT 19,63 58,9 78.5 117.8 20 SEt IN 16,49 49,5 66.0 82.5 99.0 unscrew anti-clockwise to remove the cover.
In the case of a rubber cover, the lock can be released easily by hitting the round tab on the cover with a plastic hammer. 3. Clamp arm In the case of a metal cover, the lock can be released easily by opening the cover and hitting the tab of the knuckle joint with a plastic hammer. The clamp arm may interfere with the cylinder body depending on the mounting method.
Avoid excessive torsional moment or bending moment other than those caused by the equipments own weight as this can cause damage. Support external piping separately. 3. Piping materials without flexibility such as steel tube piping are prone to be affected by excess moment load and vibration from the piping side. Use flexible tubing in between to avoid such an effect. 1100
When fluid is exhausted from the port 12(P1), the valve r connected with the piston t is closed by the return spring y. When valve opens When pressurized air enters through the port 12(P1), the valve piston moves upward by the pilot air that enters below the piston and the valve element opens.
I Wlndow comparator mode Exact detection of atmospheric pressure ZSE The hysteresIs is 2digitS, so separate PI from P2 by 5dlg~s or more and set them. tSE : The hysteresIs IS 3 digits, so separate PI from P2 by 7 digitS or more and set them. 01 digit IS the minimum pressure display unlt.
Avoid damage by always handling the switch by the main housing. Freon G Leakage Inspection The welded section IS helium leak lested. SMC recommends TSJ type fittings (With ferrule) such as Swagetok"
Since a built-in pneumatic dust collector blows the sucked in dust to the exhaust port by the power of compressed air, dust will not remain inside the dust collector.
Internal volume of filter container The product can be used as a small capacity air tank by removing the element. Following is the volume of filter containers of Series AFF and Series AM (when the element is removed). Caution 1.
After that, incline the lever by 90 and confirm that the indicator light is not on and does not show either red or green.
Set the operation pressure by using the graph as guidelines. (Applicable to the round bar, roller, and chamfered type.)
Confirmation of Allowable Load Weight by Each Application Selection conditions: Determine which of the conditions below matches your intended application, then choose one of the selection graphs that follow.
Do not scratch or gouge the linear guide by striking it with other objects. Since the linear guide is specially treated for maximum suppression of particulate generation due to sliding, even a slight scratch can cause malfunction and loss of durability, as well as a danger of degrading the particulate generation characteristics. Speed Adjustment Caution 1.
If intermediate stop by external stopper is done, avoid ejection. If ejection occurs, it may cause damage. In the case the slide table is stopped at an intermediate position by an external stopper then forwarded to the front, return the slide table to the back for just a moment to retract the stopper, then supply pressure to the opposite port to operate slide table. 2.
Air and oil are adjusted with varying quantities by the air for mist from the mixing valve (9) and oil adjustment needles (10) and (11).