VT307 (Refer to Figure 1.) 4) Remove the cable gland (4) and plain washer (5) and rubber seal (6). 3. Wiring 1) Passing through the cable (7), cable gland (4), plain washer (5), rubber seal (6) in this order, and then insert into the housing (2). 2) From the terminal block (3), loosen the screw (11), then pass the lead wire (10) through, then again tighten the screw (11).
Selection of air quality by purpose For these cases, degree of quality is 15 4 +3 5 specified as 1, 4, and 2 respectively. 40 5 +7 25 Refer to Guide (1). Refer to Guide (2). Refer to Guide (3). Refer to below piping system chart. Refer to Guide (4) page 14-14-4.
AF AR 4 - 1) 5 2) 3) 5 4) 1 ISO VG-32 2-2. 1) 2) 3) 4) 5) 6 7) 5 - 8 9) , 10) 11) 3 1) P10 [2-6.] 2) 3) 4) 5) 6) 7) (40) 6 - 2-3. 1) 1 P10 [2-6.] fR Ft N () mm 1. (MPa)=(MPa)+{(kg) 2)} X /(mm ,, 2) 3) 4) 7 - 5) 6) 7) 8) 9) 24. 1) 2) 3) 8 - 1) 2) 1.52 2 2. 2-5. ,AS 9 - 2-6. P7.1. 1.
DIN terminal: VP3145-D Conduit terminal: VP3145-T A B A B VQZ VZ VS Conduit terminal with indicator light (TL) G 1/2 Light Light Max. 11 Applicable cable 6 to 12 VFN G 1/2 Rc 1/4 Rc 1/4 ( ): With indicator light (TL) 4-10-5 6 Series VP3145/3165/3185 Dimensions: VP3165 Grommet: VP3165-G A B G 1/2 Manual override Lead wire length 200 mm External pilot port Rc 1/4 Rc 1/4 (PE port) Courtesy
B: Locking slotted type 4 1 6A 8A 10A 10A 15A 20A 25A 32A 40A 50A 1 8 1 4 3 8 3 8 1 2 3 4 220 VAC 50/60 Hz 10 5 6 24 VDC 12 VDC 240 VAC 50/60 Hz 7 15 2 9 Other Nil: Non-locking push type 20 3 Option Valve size 5 to 7 25 4 1 1 1 2 32 5 1 4 1 2 40 50 6 7 Note) Air operated only Electrical entry/ With light/surge voltage suppressor E GS G Grommet with surge voltage suppressor Grommet Grommet
Product Specifications . 5 2.1 Features of the Setting software . 5 2.2 Applicable PC . 5 2.3 Applicable controller . 5 3. Start-up . 6 3.1 Preparation . 6 (1) Software installation . 6 (2) Installation and wiring . 6 3.2. Start-up . 6 (1) Supply of power . 6 (2) Start-up of the Controller setting software . 6 (3) Alarm check . 8 4.
Station number 20 (No.2) 2 (No.6) 1 (No.7) 40 (No.1) 8 (No.4) 4 (No.5) 10 (No.3) SW2 OFF 1 OFF OFF OFF OFF OFF OFF ON 2 3 4 OFF OFF OFF OFF OFF ON OFF 6 5 4 3 2 1 ON ON OFF OFF OFF OFF OFF ON ON : Switch No.5 and No.6 are unused. (Turn them OFF.) OFF OFF OFF OFF ON OFF OFF : : : : : : : : HOLD/CLR setting (Switch No.1) The setting is as follows.
Otherwise it can cause failure or malfunction of the system. 11/4 54 mm Temperature upper limit exceeded Flow range, unit specification and mounting of temperature sensor are displayed Set value Sets the ON or OFF point of the switch output. 50 oC 11/2 54 mm The fluid temperature is above 110 oC. Reduce the fluid temperature.
CJ-CF006 CJ-CR006 6 6 8 11 5 8 6 M3 x 0.5 10 CJ-T010B CJ-CF010 CJ-CR010 3.3 10 8 10 13 6 10 8 M4 x 0.7 29 18 2 9 40 22 32 12 8 4.5 3.1 +0.048 0 16 CJ-T016B CJ-CF016 CJ-CR016 5 16 10 12 15 7 12 10 M5 x 0.8 35 20 14 48 28 38 16 10 5.5 6.4 2.3 +0.048 0 6-3-11
.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com 14-4-11 Miniature regulator ARJ310 Small, compact Allows smaller mounting pitch Bracket Pressure gauge M5 0.2 to 0.7 1 8 / to 2 1 4 Pilot operated regulator AR425-925 AR435-935 Compact manifold regulator ARM10/11 / 14-4-15 Internal pilot type Relieving
0 P1(11) port u R(4) Exhaust port r !5 o !7 A(2) port P2(12) port w !2 !6 !4 !
Replaceable Bellows 5 Customer can replace bellows. 534
JIS B 2401G35 5 pcs. u O-ring 14-20-25 5 Series AMD Dimensions AMD150 to AMD650 Accessory D: With auto-drain (N.O.) Drain cock: Black One-touch fitting C: With auto-drain (N.C.)
) 4 (A6063) C C C C D D D D Body (material: A6063) K C C C C E E E E E E E E KF flange F F F Fn n n n (KF) () Heater (option) Auto switch H H H H J J J J G G G G B B B B A A A A A A A A Model A B C D E Fn G H J K XLC-25 50 120 48 1 12 40 26 39 27.5 8 XLC-40 65 171 66 2 11 55 41 63 36 9 8 XL-OMO0001-A 5 Guaranteed period and range The warranty period is 2 million cycles (under SMC endurance
R R 1. 2. 2 9 - 3-7 1 ON OFF ON ON 1 2 1 1 1 2 3 3 0.3~0.5mm 4 5 0.3~0.5mm 10 - 2 ON OFF ON ON 1 2 1 1 1 2 3 3 0.3~0.5mm 4 5 0.3~0.5mm 11 - M2.54 5 6 5~6mm 0.05~0.1 Nm90 D-Y59/Y69/Y7P/Y7PV D-M9(V) D-Y7W/Y7WV D-M9W(V) D-M9A(V)L MHL2-10D 0.8 0.3 MHL2-16D 0.5 0.4 MHL2-20D 0.5 0.7 ON MHL2-25D 0.5 0.6 OFF MHL2-32D 0.5 0.6 MHL2-40D 0.5 0.9 1. 2. 12 - 3-8
The MXJ air slide tables integrated front mounting part and table result in a highly accurate, rigid top and front mounting surface. Clean specification styles are available with no dimensional changes. Several options are available for both the standard and the clean series MXJ. These options include a symmetric style, stroke adjusters, axial piping and auto switches., Cylinder, Air,
11 Symbol B A (A) 4 (B) 2 2 x Rc1/8 (Port 2, 4) 38.2 26.2 2 x M5 x 0.8 (Port 3, 5) 12 14 Rc1/8 (Port 1) 3 (EB) 1 (P) 5 (EA) Total Travel (T.T.) 2.5 Full Operating Force (Reference value)(F.O.F.) 55 N (at 0.5 MPa) 530.2 1590.2 Safety Instructions Be sure to read Handling Precautions for SMC Products (M-E03-3) before using.
EX500-DX B Install the product using 2 M5 screws x 20 mm minimum with a head 9 to 11. NOTE Refer to the product catalog or SMC website (URL http://www.smcworld.com) to obtain more detailed information about product specifications. 1 3 5 7 9 11 13 15 The direct current power supply to combine should be UL1310 Class 2 power supply when conformity to UL is necessary.
(Refer to 7-5. Emergency Stop of Operation Manual (K35-OMW0030). For detailed description of the signals, refer to the following pages. 15 (2) Internal circuit (Numbers in brackets indicates the pin numbers) (5) PWR_DC24V LF (6) PWR_GND Output signal GND (9) CTR (10) CYL (11) VAL (16) RF (17) PWR Max.
The Deteriorating Effect of Ozone . 5 Causes and Progression Deterioration due to Ozone Fluctuation of Ozone Concentration in Pneumatic Circuits 4. Ozone Resistance of Standard (HNBR) Products . 7 Setting Endurance Test 5. Ozone . 8 What is Ozone?