44 Comparison with KFG0806 Barb Sealing performance and holding of tube are secured by backup from the barb. Antistatic soft nylon Antistatic polyurethane Note) For tubes marked , check the appropriate size. (Pages 322, 328) Applicable tubing Connection thread Page Grease-free Metric size Inch size R, Rc NPT P.322 to 326 Can be used with steam.
Note 3) See How to Order below for items represented by .
If this occurs, wait until the oil temperature rises by a warm-up operation, then check if this is caused by clogging. Once the differential pressure indicator is actuated, the indication continues to be displayed until the indicator is reset (by depressing the reset button), even if the pump stops operating.
Avoid excessive torsional moment or bending moment other than those caused by the equipments own weight as this can cause damage. Support external piping separately. 3. Piping materials without flexibility such as steel tube piping are prone to be affected by excess moment load and vibration from the piping side. Use flexible tubing in between to avoid such an effect. 1100
Gray (40) (10) (8) ( 4.1) (6.9) Black Red With power saving circuit Electrical Circuit (with power saving circuit) Red (+) Power consumption is reduced by approximately 75% compared with the standard product by eliminating the need for electrical current for holding.
SP ZCUK Max.660 L/min (ANR) 5,40,80 m AMJ Large flow capacity Nominal filtration rating AFJ AFJ AMV Large flow type (P=4 kPa) Elements can be reused by washing them. For 40 m and 80 m ZH -X185 Related Products Water drops can be removed. Water drop removal ratio: 80%. At recommended flow rate (representative values).
The M12 cable, AS-i standard cable and connector for T-branch are not supplied by SMC. Contact each manufacturer for the catalogue details etc. Wire the cable for AS-Interface line so that the total voltage drop is 3 V or less.
Removing the panel mount adapter The product with panel mount adapter can be removed from the installation by removing 2 screws and releasing the hooks at the sides. The hooks can be released by inserting a suitable thin card. Pull the panel mount adapter to the front, and remove the product.
This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switch-mode power supply and the product, or by using a series power supply instead of a switch-mode power supply. The following instructions must be followed during maintenance: Turn off the power supply.
each 50 stroke 0.26 0.35 0.49 0.01 0.01 0.02 0.02 0.03 Additional weight by air cushion 0.03 0.03 0.03 0.01 0.01 0.02 0.03 0.06 Additional weight by long stroke 0.10 0.19 0.26 Calculation example: CG1LA20-100 (Foot, 20, 100 stroke) Basic weight0.21 (Foot, 20) Additional weight0.05/50 stroke Cylinder stroke100 stroke Additional weight by air cushion0.01kg 0.21+0.05 X 100/50+0.014=0.32kg
Speed Controller Adjustable by Flat Head Screwdriver with One-touch Fitting. Series AS * * * 1F-D Speed Controller Adjustable by Flat Head Screwdriver with One-touch Fitting Elbow Type/Universal Type . Specifications. How to Order . Construction. Dimensions . Series AS * * * 1F-D Speed Controller Adjustable by Flat Head Screwdriver with One-touch Fittings In-line Type. Specifications.
As a rule, this is equivalent to 2 or 3 turns with a tool after tightening by hand. Be careful of damage due to over tightening. When using miniature pipe fittings, tighten by an additional 1/4 turn after hand tightening. Further, in cases such as a universal elbow or universal tee which have gaskets in 2 locations, the additional tightening is doubled to 1/2 turn. 1.
The movement of piston 1 is detected by switch assembly 3 and outputs ON and OFF signals. The set pressure can be adjusted by turning adjustment screw 4, which adjusts the spring force. 1.9-4
As a Socket case Hold surely by inserting the both of tube and barb. Possible to connect in the required position by the convex and concave for engagement. result, separate transportation of panel Plug and machinery equipment and backup Easy insertion of tube by the floating mechanism to adjust to the case hole. unit exchange are made possible.
To detach a connector, remove the pawl from the groove by pushing the lever downward with your thumb, and pull the connector straight out.
/N.O. type can be switched by supplying air to port 1 (P) or 3 (R). 2 way valves and selector valves can also be freely used. Easy manual operation S070 Since manual overrides are located in 2 directions, on the top and on the side of the valve, manual override operation is possible and is unaffected by mounting space and piping direction, etc.
Mount it by referring to how to switch over from N.C. to N.O. specifications. Universal porting permits convertibility N.C./N.O. by a simple 180 degree rotation. Mounting conditions for N.C. and N.O. is indicated as below figure. Valve Exhaust port type N.C. N.O. Common exhaust Caution 1. Each valve is fixed to the manifold base with two M4 mounting screws.
By connecting each block with a connector, changes to manifold stations are greatly simplified. SV Connector wiring diagram For both serial and parallel wiring, additional manifold blocks are sequentially assigned pins on the connector. This makes it completely unnecessary to disassemble the connector unit.
Note 6) Window comparator mode Since hysteresis will reach 3 digits, keep P_1 and P_2 or n_1 and n_2 apart by 7 digits or more. (In case of output OUT2, n_1, 2 to be n_3, 4 and P_1, 2 to be P_3, 4.)
(Use clean, dry, and nonfreezing air) However, as the stroke increases, it will likely be affected by the weight of the moving parts and the pressure will likely increase by approx. 0.003 to 0.005 MPa. This is due to an offset load from the weight of the rod. Note 2) Refer to precautions on page 18 regarding lubrication.