PF3WBCSR.eng

Otherwise it can cause failure or malfunction of the system. 1 L+ Brown 18 to 30 VDC 2 N.C.

PF3W7x-X445.eng

Set value Sets the ON or OFF point of the switch output. 50% of rated flow 1 L+ Brown 18 to 30 VDC SET button Hysteresis Setting of hysteresis can prevent chattering. 5% of rated flow 2 N.C.

AC Servo Motor Driver (Pulse input type/Positioning type)

The MR Configurator2 software will be added to the PC. 5.2 Basic driver set-up for Initial Test Drive Switch on the 24 VDC and 230 VAC power supply to the LECSA driver and wait until the driver display flashes as shown below. 19 - 5.2.1 Start up the Setup software (MR Configurator2TM) Connect the PC and LECSA using the USB cable. Turn on the power of the LECSA.

Rotary Table

Additionally, note that the 12 VDC relay does not apply to the auto switch. -12- 11. Pay attention to leakage current. <2-wire type> Current (leakage current) flows to the load to operate the internal circuit even when in the OFF state.

LEC-OM034xx

Gateway Controller input power supply 24 VDC unit CN Terminating Resistor (120 1/4W) CN4 CN4 CN4 Controller (LEC) Controller (LEC) Controller (LEC) * Refer to section 8. CN1: Controller IF communication connector (CONT) 23 - Caution Do not pull out the cable between the gateway unit and the cable, or cut off the power supply to the controller (LEC).

Fieldbus Device Handheld Terminal

Refer to the operation manual of the unit, and supply Power supply error. a voltage of 24 VDC 10% to the SI unit power supply for control and input. 1 POWER LED is OFF. Connection failure of the cable for Handheld Terminal. Check the cable for Handheld Terminal. Check the error in the diagnostic data check mode.

HEAVY DUTY STOPPER CYLINDER

E2E-X2D1-N Output type Normally open Power supply voltage (Operating voltage range) 12 to 24 VDC (10 to 30 VDC), Ripple 10% or less (P-P) Current consumption (Leakage current) 0.8mA or less Response frequency 1.5 kHz Control output (Switching Capacity) 3 to 100 mA Indicator light Operation indication (Red LED), Set operation indication (Green LED) Ambient temperature -25 to 70 (No freezing

Coolant Valve: Air Operated/External Pilot Solenoid VNC Series

12 VDC B: Slotted locking type B (tool required) 7 240 VAC 50/60 Hz 15 (11) 2 Semi-standard For other rated voltages, please consult with SMC. 20 (14) 3 25 (16) 4 1 1 1 4 32 (22) 5 1 B 1 4 Flange 32F Nil: Non-locking push type 40A 1 1 2 Valve size 2 to 9 40 (28) 6 1 B 1 2 Flange 40F 2 50A 50 (33) 7 50F 2B Flange Semi-standard 2 B 1 2 Flange 65F 65 (45) 8 Electrical entry/With light/surge

AFF

IN-OUT reversal direction With differential pressure switch (125 VAC, 30 VDC) 5, Note) With differential pressure switch (30 V) 5, Note) With element service indicator Degreasing wash,6 white vaseline Auto Drain Specifications/Option Combinations 4 Drain piping and piping for a stop valve such as ball valve are required. 5 Differential pressure gauge is included, (but not assembled). 6 Only

105.0 to 105.0 kPa500 kPa0.1 kPaAir, Non-corrosive gas, Non-flammable gas12 to 24 VDC ?

105.0 to 105.0 kPa500 kPa0.1 kPaAir, Non-corrosive gas, Non-flammable gas12 to 24 VDC ?

105.0 to 105.0 kPa500 kPa0.1 kPaAir, Non-corrosive gas, Non-flammable gas12 to 24 VDC ?

105.0 to 105.0 kPa500 kPa0.1 kPaAir, Non-corrosive gas, Non-flammable gas12 to 24 VDC ?

105.0 to 105.0 kPa500 kPa0.1 kPaAir, Non-corrosive gas, Non-flammable gas12 to 24 VDC ?

105.0 to 105.0 kPa500 kPa0.1 kPaAir, Non-corrosive gas, Non-flammable gas12 to 24 VDC ?

105.0 to 105.0 kPa500 kPa0.1 kPaAir, Non-corrosive gas, Non-flammable gas12 to 24 VDC ?

105.0 to 105.0 kPa500 kPa0.1 kPaAir, Non-corrosive gas, Non-flammable gas12 to 24 VDC ?

105.0 to 105.0 kPa500 kPa0.1 kPaAir, Non-corrosive gas, Non-flammable gas12 to 24 VDC ?

105.0 to 105.0 kPa500 kPa0.1 kPaAir, Non-corrosive gas, Non-flammable gas12 to 24 VDC ?

105.0 to 105.0 kPa500 kPa0.1 kPaAir, Non-corrosive gas, Non-flammable gas12 to 24 VDC ?