Large Size Vacuum Module: Series ZR Do not expose it to direct sunlight.
Do not expose the product to direct sunlight for an extended period of time. 3. Do not use in a place subject to heavy vibrations and/or shocks. 4. Do not mount the product in locations where it is exposed to radiant heat.
Model (Made to Order) PPA Pressure range Note) Connection thread (MPa) Indication unit Model AL MPa 0 to 1.0 M5 (Female thread) G27-10-M5-X201 Note) Do not apply more excessive pressure than max. pressure display. It will be a cause of malfunction.
Do not use the materials for buffer face which might cause to spark by collision. Load Warning Allowable eccentric angle 1 < 5 1.
The graphs do not show the loadable mass. Refer to the Model Selection for the loadable mass.
Do not apply external force to the coil. Apply a wrench to the exterior surface of the piping joint at the time of tightening. 3. Do not use heat insulators, etc. to keep the temperature at the coil assembly. Do not use a tape heater for freeze prevention except on the piping and body. If may cause the coil to burn. 1.
Do not poke the inside of the piping port with a stick. The rectifier could break, making the product unable to sustain the desired performance. 4. Do not touch terminals or connectors when energizing the product. It could cause electric shock, malfunction, or damage to the switch.
Do not use a lead wire longer than 30 m. Wire the DC (-) line (blue) as close as possible to the power supply. Operating environment Do not use the product in an environment where the product is constantly exposed to water or oil splashes. Otherwise it can cause failure or malfunction. Take measures such as using a cover.
As the connected actuator will start confirm that it is safe to do beforehand.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
These dimensions do not include possible protrusions such as a breaker handle.
Do not use the materials for buffer face which might cause to spark by collision. Load Warning Allowable eccentric angle 1 < 5 1.
Open/ Close success: default output DO[101] Open / Close failure: default output DO[102] workpiece drop detection: default output DO[103] * Digital output port can be selected within DO[101] to DO[112] * you select the same digital output port for different status signals, a warning message will be displayed. 2. Test run The manual operation of the air gripper unit can be checked.
Do not use the product in an environment where corrosive gases or fluids can be splashed. Otherwise damage to the SI can result, causing malfunction. Do not use the product in an area where surges are generated.
Do not work when intoxicated or feeling ill. Accidents may occur if disregarded.
Do not use until you verify that the equipment can operate properly. After mounting, repair or modification, etc., connect the air supply and electric power, and then confirm proper mounting by means of appropriate function and leak inspections. Do not let chips or extraneous material enter inside the cylinder from the inlet.
When performing neutralization, do not input the ionizer stop signal.
Piston rod Do not turn the screws at the bottom. Do not damage the sliding surface of the piston rod of the shock absorber. Otherwise, impaired durability and return failure can result. Damage is not allowed. Shock absorber is a consumable. Replace the shock absorber when the energy absorption performance is reduced.
Therefore, do not use it with or expose it to the following chemicals: paint thinner, carbon tetrachloride, chloroform, acetic ester, aniline, cyclohexane, trichloroethylene, sulfuric acid, lactic acid, water-soluble cutting oil (alkalinic), etc. 2. Do not expose it to direct sunlight.
Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not use in a place subject to heavy vibration and/or shock. 3. Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction. 4.