Cylinder

Bore6:CO.5 ~ .+~ MM 4>1O, 1S:Cl n\ ~I +I." ~\ 10>1 f!-f.F F ", "I , H I' f.'5., I1tJ F E Rod end without ~ H S R thread , I Z oG H K l MM 1 s I z..q sst I lost IS" , 5" 16!J. IS'" IN 1 5" lOst ~ 15s1 ' A ... B C E F 15 12 ' 27 31 7 16.5 22.5 29 19 14 4.2 M5 x O.8 i M22 x 1.5 I 20 23.5 29.5 36 5 , 37.5 43.5 50 ' 6 'a~e size ' .rom) .

NVZ1000//3000/5000 4,5 Port Solenoid Valve/Rubber Seal Type

'i,-.1-)^' l z N F Noz l!

Mechanically Jointed Rodless Cylinder Series MY2 ø16, ø25, ø40 1

Reference formulas [Dynamic moment at impact] Use the following formulas to calculate dynamic moment when taking stopper impact into consideration. m F FE a M 1.4 = 1.4a (mm/s) FE = agm Note 4) 100 1 ME = FE L1 = 0.05a m L1 (Nm) Note 5) L1 ME g : Load weight (kg) : Load (N) : Load equivalent to impact (at impact with stopper) (N) : Average speed (mm/s) : Static moment (Nm) : Impact speed

LEKF-OMZ0035

When the product repeatedly cycles with partial strokes (see the table below), operate it at a full stroke at least once every 10 strokes. Otherwise, lubrication can run out. 5.

ZSE30A(F)/ISE30A

Prevents operation errors such as accidentally changing setting values. 0 Applied pressure + F Zero-clear function Indicated value at the time of shipment Adjustable range of display calibration function This function clears and resets the zero value on the display of measured pressure.

,,: ,.

Prevent contaminant's f rom entering fittinge and cartridges.

Designed to work with fluids up to 90ºC, these switches incorporate a built-in temperature sensor so both flow and fluid temperature can be effectively monitored at the same time. 

3 Port Solenoid Valve

holding) with power saving circuit Note 1) Note 1) With the 0.1 W DC specification, keep the vibration/impact within10/50 m/s2. 0.35 W DC at inrush (20 ms) and 0.1 W DC at holding.

Mechanically Jointed Rodless Cylinder with Brake, Hy-rodless Cylinder Series ML1C ø25, ø32, ø40 1

Set the supply pressure at 0.25 to 0.5 MPa. If setting at less than 0.25 MPa, malfunction of the release brake may occur. If line pressure is used directly as supply pressure, any fluctuation in pressure will appear in the form of changes in cylinder characteristics.

Mechanically Jointed Rodless Cylinder with Brake, Hy-rodless Cylinder Series ML1C ø25, ø32, ø40 1

Set the supply pressure at 0.25 to 0.5 MPa. If setting at less than 0.25 MPa, malfunction of the release brake may occur. If line pressure is used directly as supply pressure, any fluctuation in pressure will appear in the form of changes in cylinder characteristics.

Air Cylinder/Low Friction Series MB l Q ø32, ø40, ø50, ø63, ø80, ø100

F B With pressure at head side With pressure at rod side *Refer to p.5.3-2 for further information on the auto switch.

1

) 2 x 5.5 Without spacer With spacer 2 x M5 thread depth M 15 15 Spacer Grommet: GS Flat terminal: F Conduit: C 280 G F F G 11 300 G F Terminal part Flat terminal connector 11 23 9 H C 15 6.5 H C H C G1/2 Terminal: T DIN terminal: D F G Applicable cable O.D.: 6 to 12 F G Width across flats 22 G1/2 32 (44) H 31.5 25 C H C G1/2 J J Dimensions [mm] Model A B Bs C D E F L M P [inch] Grommet:

CJ2X/CUX/CQSX/CQ2X/CM2X

Bore size L F G D Foot style Rod side flange style Head side flange style Double clevis style 12 16 20 25 12 mm 16 mm 20 mm 25 mm Cushion/Rod end thread Nil C M Standard (Rod end female thread) With rubber bumper Rod end male thread Combination above is possible.

15

Sum of guide load factors Load mass (m) Allowable load mass on guides (mmax) + = Static moment (M) Note 1) + 1 Dynamic moment (ME) Note 2) Allowable static moment (Mmax) Allowable dynamic moment (MEmax) Note 1) Moment caused by the load etc., with cylinder in resting condition Note 2) Moment caused by the load equivalent to impact at the stroke end (at the time of impact with stopper) Note

CJ2X/CUX/CQSX/CQ2X/CM2X

Bore size L F G D Foot style Rod side flange style Head side flange style Double clevis style 12 16 20 25 12 mm 16 mm 20 mm 25 mm Cushion/Rod end thread Nil C M Standard (Rod end female thread) With rubber bumper Rod end male thread Combination above is possible.

PF3W7.eng

(Example for 4 L/min type the above ) In measurement mode, when the button is pressed for 2 seconds or longer, [F 1] is displayed. This [F ] indicates the mode for changing each functional setting.

PF3W7x-X445.eng

Function selection mode In measurement mode, press the SET button for 3 to 5 seconds to display [F ] on the main screen. Select to display the function to be change [F ].

Support Guide/11-LEFG Series

0 ) depth 3 4 x M5 x 0.8 thread depth 8.5 38 50 3.5 3H9 (+0.025 0 ) depth 3 A (Table traveling distance) L 51 (52) 10 10 58 38 48 38.5 (48) 26 24 n x 4.5 Vacuum port Rc1/8 48 120 F D x 120 (= E) B Dimensions [mm] Dimensions [mm] Model L A B n D E F 11-LEFG25-S-50 180 57 160 4 20 11-LEFG25-S-100 230 107 210 Model L A B n D E F 11-LEFG25-S-450 580 457 560 10 4 480 35 11-LEFG25-S-500 630

Mechanically Jointed Rodless Cylinder with Protective Cover Series MY1W

In such cases, install a side support at the intermediate stroke position.

Series CJ2Y ø 10, ø 16 Smooth Cylinder Double Acting, Single Rod

FC Mounting hole B 0 0.3 A F NA FT NB FX FZ H S + Stroke F Z + Stroke Refer to page 8 for details of the mounting nut.