Soft Start-up Valve AV2000/3000/4000/5000 1 Do not use valves in such environments where corrosive gases, chemicals, or brine or water or steam is airborne, or where valves can be directly exposed to any of those. 2. Do not use in an explosive environment. 3. Do not use in locations influenced by vibrations or impacts. 4. A protective cover, etc., should be used to shield valves from direct sunlight. 5.
Do not use with pressure or temperature beyond the specification range.
28 'Vacuuh to 30o FSIG (20 Kglrcm?).
Clean Room Rodless Cylinder Series CYP 15, 32 MX MTS MY CY MG CX D-X 20Data Magnetically coupled rodless cylinder for transfer in clean environments. 8-17-1 Low particle generation: 1/20 Long stroke (Max. 700 mm) (compared to previous series) High cleanliness is achieved with non-contact construction of the cylinder tube exterior and a stainless steel linear guide (specially treated).
Controller power Power supply voltage: 24 VDC +/10%, 3A or more supply DC24V (Do not use inrush current limiting type) 20 AWG / 0.5 mm2 Use a single multi-strand wire for each terminal. Strip the wires and twist the wires together, as shown. Stripped wire length Power supply cable 8mm The insulation should be rated to withstand a temperature of 60oC minimum.
28 'Vacuuh to 30o FSIG (20 Kglrcm?).
Do not use fluid containing solid matter. This will cause faulty operation. IR IRV VEX SRH SRP SRF SRF ITV IC ITVH ITVX PVQ VY1 VBA VBAT AP100 891
Do not operate with the magnetic coupling out of position. If the magnetic coupling is out of position, push the external slider by hand (or the piston slider with air pressure) back to the proper position at the stroke end.
For details, refer to pages 3-7-19 and 3-7-20.
Do not operate or set with wet hands. This may lead to an electric shock. End plate bracket (EX600-ZMA2) SUPPLIERS DECLARATION OF CONFORMITY Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Connector (Base only) (2) Add more units.
This product is not designed to be explosion proof. 1.2 to 1.6 Orange ZS-28-C-2 1.0 to 1.2 Green ZS-28-C-3 1.2 to 1.6 Blue ZS-28-C-4 22-20 0.3-0.5 Do not use the product in a place where static electricity is a problem. Otherwise it can cause failure or malfunction of the system. 1.6 to 2.0 Grey ZS-28-C-5 Troubleshooting Do not cut the insulator.
Do not use in an atmosphere where the electro-pneumatic proportional valve is in direct contact corrosive gases, chemicals, salt water, water, steam. 2. Do not use in an environment where flammable gas or explosive gas exists. The products do not have an explosion proof construction. 3. Do not use in a place subject to heavy vibration and/or shock. 4.
Do not use valves where there is direct contact with, or in atmospheres of, corrosive gases, chemicals, salts water or steam. 2. Do not use in an explosive atmosphere. 3. Do not use in locations subject to vibration or impact. Confirm the specifications for each series. 4 - 4. A protective cover should be used to shield valves from direct sunlight. 5.
Do not rotate the screw more than 30 degrees for additional tightening. (The maximum tightening torque: 0.2 Nm) 3. Do not mount the product in a place where dust will be stirred up by the exhaust air from the product and affect peripheral equipment. 4. Do not mount the product in a location where air from the product will be directly exhausted to the workpiece. 5.
Do not apply negative pressure. It may result in malfunction. Should they remain, they could cause malfunction. 3. When connecting pipes and fittings, etc., be sure 3. Do not supply air pressure from ports other than that neither chips from the pipe threads nor sealing material get inside the valve.
Free flow Controlled flow Model Port size Applicable cylinder bore size (mm) Effective area (mm2) Effective area (mm2) Flow rate (/min (ANR)) Flow rate (/min (ANR)) Weight (g) 4.7 AS1000-M3 M3 x 0.5 20 0.3 20 0.3 2.5, 4, 6 33 AS1000-M5 M5 x 0.8 90 1.4 80 1.2 6, 10, 16, 20, 25 90 AS2000-01 1/8 340 5.2 250 3.8 20, 25, 32, 40 115 AS2000-02 1/4 340 5.2 250 3.8 130 AS3000-02 1/4 810 12.3 810 12.3
Note Description AW10, 20 AW30 AW40, 40-06 1 2 Body Bonnet Platinum silver Black Zinc die-cast Aluminum die-cast Polyacetal Replacement parts Part no. Description No.
If the installation is using accurate control, wait until the product has warmed up (approximately 20 to 30 minutes). 2 s button (DOWN) Easy setting Function selection mode Attaching the connector to the sensor wire Strip the sensor wire as shown to the right. (Do not strip the wire insulation) 20 mm or more Cover Output OUT1 LED (Green): LED is ON when OUT1 is ON.
Note1) To avoid the damage of O-ring and adjustment part, do not turn bypass valve adjusting bolt(13) farther than the point where turning is stopped at both ends. Note2) Do not apply pressure to the operation port during adjustment. Note3) Bypass valve is fully open at ex-factory.
20 20 0.15MPa 0.15MPa 0.15MPa 10 10 10 0.2MPa 0.2MPa 0.2MPa 100 200 300 0 100 200 300 0 100 200 300 0 Detection distance (m) Detection distance (m) Detection distance (m) Example 1) When requiring 300m detection, select the detection nozzle of 1.0 with supply pressure 0.2MPa.