Rated Pressure Range: H (-0.1 to 2 MPa), Output Specification: R (NPN Open Collector 2 Outputs + Analog Voltage Output), Unit Specification: Unit Selection Function, Switches w/Unit Selection not Permitted for Use in Japan, Piping Specification: F02 [G1/4, (M5, Female Threaded)], Piping Direction: L (Bottom Ported), Lead Wire: W (Lead Wire w/Connector, 5-core, 2 m Lead Wire, Waterproof)

Rated Pressure Range: -0.1 to 1 MPa, Output Specification: R (NPN Open Collector 2 Outputs + Analog Voltage Output), Unit Specification: Unit Selection Function, Switches w/Unit Selection not Permitted for Use in Japan, Piping Specification: F02 [G1/4, (M5, Female Threaded)], Piping Direction: Rear Ported, Lead Wire: W (Lead Wire w/Connector, 5-core, 2 m Lead Wire, Waterproof)

Rated Pressure Range: -0.1 to 1 MPa, Output Specification: R (NPN Open Collector 2 Outputs + Analog Voltage Output), Unit Specification: Unit Selection Function, Switches w/Unit Selection not Permitted for Use in Japan, Piping Specification: F02 [G1/4, (M5, Female Threaded)], Piping Direction: Rear Ported, Lead Wire: W (Lead Wire w/Connector, 5-core, 2 m Lead Wire, Waterproof), Bracket: D

Series: 25A-PFM7, Flow Rate Range: 11 [2 to 100 (50) L/min], Port Size: F02 (G1/4), Piping Entry Direction: Straight, Output Specification: B (2 PNP Outputs), Unit Specification: Unit Switching Function, Operation Manual: With Instruction Manual, Calibration Certificate: None, Connector: W (Lead Wire w/Connector, 2 m; Rubber Cover for Connector, Silicon Rubber), Option: R (Bracket for w/o

Number of Ports: 2 Port, Body Option: Side Mounting, Port Size: F02 (G 1/4), Actuator Type: 32 (Push Button, Extended), Suffix: R (Red)

Number of Ports: 2 Port, Body Option: Side Mounting, Port Size: F02 (G 1/4), Actuator Type: 30 (Push Button, Mushroom), Suffix: R (Red)

Number of Ports: 3 Port, Body Option: Side Mounting, Port Size: F02 (G 1/4), Actuator Type: 30 (Push Button, Mushroom), Suffix: R (Red)

Number of Ports: 3 Port, Body Option: Side Mounting, Port Size: F02 (G 1/4), Actuator Type: 34 (Twist Selector, 2 Position), Suffix: R (Red)

Number of Ports: 3 Port, Body Option: U (w/Bottom Mouinting Thread), Port Size: F02 (G 1/4), Actuator Type: 35 ( Twist Selector, 3 Position), Suffix: R (Red)

Body Size: 4 (1/4 Basis), Port Size: F02 [Cylinder Side (R(PT)1/4) Pilot Port (G(PF)1/8)], Applicable Tube OD: Ø8, Lock Nut: J (Round)

Body Size: 4 (1/4 Basis), Port Size: F02 [Cylinder Side (R(PT)1/4) Pilot Port (G(PF)1/8)], Applicable Tube OD: Ø6, Lock Nut: J (Round)

Body Size: 4 (1/4 Basis), Port Size: F02 [Cylinder Side (R(PT)1/4) Pilot Port (G(PF)1/8)], Applicable Tube OD: Ø8

ISE70/75/75H

DOWN OUT1 U P SET ZS-31-A Bracket Note: Mounting screws are not included.

Size: 3/8, Thread: G, Port Size: 1/4, Accessory: -, Option 1: -, Option 2: -

Old AL series lubricators from old AC series modular F.R.L. units (2 digits: AL□□) can be replaced with lubricators from the AL□□-A series, which are interchangeable.
In addition, old AL series lubricators (e.g., AL3000-02) from older AC series modular F.R.L. units (4 digits: AL□□□□) can be replaced with lubricators from the AL□□-A series (AL30-02-A).

Case: [Resin] Polycarbonate Case, Drain Exhaust: -, Case Guard: -, Specification: Applicable part number: AL20-A, AL30-A, AL40-A, AL40-06-A, AL50-A, AL60-A, Type: Sight dome assembly

Refer to the table below for the storage capacity of AL-A/AL-D series lubricators.
A 1000 cm2 tank type is available for standard AL30 to 60 series products.
Details on the 1000 cm2 tank type can be found <a href="/webcatalog/en-jp/seriesList/?type=GUIDE&id=AL-A-E" target="_blank">herea>.

For AL30-A to AL60-A series lubricators, when the lubrication plug is opened under the pressure of the lubricator, air bubbles may be generated at the end of the oil passage (sometimes they are not). This is also caused by the bowl’s internal pressure being lower than the outlet pressure.

BOWL ASSEMBLY, AL30-A, AIRLINE EQUIPMENT, AF MASS PRO, 21, AF MASS PRO NO SIZE RATING, 0.22046 lb

The AL30/40/50/60 are equipped with a check valve on the body.
Therefore, lubricant can be supplied by removing the lubrication plug even when the product is pressurized.
Loosen the lubrication plug slowly, by about 1 turn, to release the pressure inside the bowl.
When pressure in the bowl is released, remove the lubrication plug and supply lubricant.