3 A G i 2 x P Port size G A 2 x P Port size b B Conduit DIN terminal D F Q S Cable 6 to 12 G1/2 F Q 280 D G1/2 45 (42) (44) 31.5 Built-in full-wave rectifier type R C C R E J J E 2 x M depth 5 H 2 x M depth 5 B B1 H G A G A B B1 2 x P Port size 2 x P Port size Bracket mounting hole a1 (VXS23, 25) a a1 (VXS24, 26) 6.5 10.5 Dimensions (mm) Model Port size P A B B1 C D E F G H J M Bracket mounting
ARP VY1D00 VY1400 IR-A Simple circuit configuration IR 1 Piping labor reduced A flexible system has been adopted.
Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.
and V124(A) cannot be mounted to the same manifold.
Therefore, internal parts of a cylinder other than rod seal are not replaceable. 2. Use caution to the popping of a retaining ring. When replacing rod seals and removing and mounting a retaining ring, use a proper tool (Retaining ring plier: Tool for installing a type C retaining ring).
A A A-A r q e w A A-A e r q w Component Parts No.
Use the table below as a guide when adjusting auto switch positions, etc.
Use the table below as a guide when adjusting auto switch positions, etc.
Next, pour water at 5 to 40C, then measure the flow rate with a pressure difference of 0.075 MPa. However, the pressure difference needs to be set with a large enough difference so that the Reynolds number does not go below a range of 4 x 104. By substituting the measurement results for formula (8) to figure out Av.
Next, pour water at 5 to 40C, then measure the flow rate with a pressure differential of 0.075 MPa. However, the pressure differential needs to be set with a large enough difference so that the Reynolds number does not go below a range of 4 x 104. By substituting the measurement results for formula (8) to figure out Av.
or less 0.5 A or less 0.5 A or less Power supply fuse 3 A 1 A 1 A Two-time Hitting Function Interrupt Operation Function A two-time hitting function has been adopted to improve the bag filter dusting efficiency.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
Once in the mounting position, use a flat head watchmakers screwdriver to tighten the included set screw. Note) When tightening the set screw, use a watchmakers' screwdriver with a handle diameter of about 5 to 6 mm.
As a rule, they should be tightened 2 to 3 turns with a tool after first tightening by hand.
Front matter 5 14 (4) Test method By attaching the equipment for testing with the test circuit shown in Fig. (3) and running water at 5 to 40C, measure the flow rate with a pressure difference of 0.075 MPa. However, the pressure difference needs to be set with a large enough difference so that the Reynolds number does not go below a range of 4 x 104.
If A is turned ON, the output turns ON. 2. Even though A is turned OFF, the output remains in ON state. 3. If B is turned ON in 2. state, the output is turned OFF. If either A or B is turned ON, cylinder is actuated.
Block off the heat with a cover, etc. 5. Do not use in locations where static electric charges will be a problem. Consult SMC regarding use in this kind of environment. 6. Do not use in locations where spatter occurs. There is a danger of spatter causing a fire.