ISO Cylinder W Double knuckle joint V (1 pc.) V (1 pc.) Standard Mounting Bracket/Accessory Part Nos.
Series CG1 precision air cylinder has 8 bore sizes and can meet any application need. The tube is impact extruded aluminum to produce an extraordinarily smooth finish, allow low break-away pressure and smooth stroke action. Eight mounting options are available. Auto switch capable. CG1, double acting, single rod cylinder with made-to-order options, Bores sizes *: 20, 25, 32, 40, 50 63 *,
(-XC6) Caution Other specifications are the same as the standard model. Dimensions q Do not use the air cylinder as an air-hydro cylinder. This will cause an oil leak. w Install without twisting the bellows. If the cylinder is installed with its bellows twisted, it could damage the bellows.
(Atlanta) 1440 Lakes Parkway, Suite 600 Lawrenceville, GA 30043 Tel: (770) 624-1940 FAX: (770) 624-1943 16850 W. Victor Road New Berlin. Wl 53151 Tel: (414) 827-0080 FAX: (414) 827-OO92 5377 Glen Alden Drive Richmond, VA 23231 Tel: (804) 222-2762 FAX: (80a) 222-5221 SMC Pneumatics Inc.
: ~ T,::;:,:' 3-w". (NPN) b-v G39 1 e , i,,",, 2-wi," K39 -1 i DiagnostiC Indication I'" 3-~,e (NPN) 1 5V, 12 \ M9NW Relay, PLe 3-w", (PNP) It . ~ .. (2-ColOr indication) 2-~-,"24 V I ( ~ .' Grommet , , 3-wi,.
Applicable shaft type: W (If shortening the shaft is not required, indicate for dimension Y.)
n i COM w hout inpul block (SDo) 58 Kir Fequires for S kit SDO . serial kit only. ..q,'options i-l stations G-l Electrical entry/Cable length A I slal o{rs w lh back orcssure check va v 1!
1 i w !8 #4 !6 A MX @1 @0 !9 MTS !0 #2 MY CY $0 MG Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com Ball bushing bearing A #5 @5 #0 CX @8 @6 D!7 !0 @1 !3 #8 !
1 i w !8 #4 !6 A @0 @1 !9 #2 !0 #1 A' For ball bushing #5 @5 #0 @8 !7 @6 !3 #8 !2 @1 !0 @9 For slide bearing y For long stroke For 100 @7 For 80, 100 View A-A' Parts list Parts list No. Description No.
4 w !7 !3 @0 !1 y !5 Component Parts Description Material Note Component Parts Description Material Note No. q w e r t y u i o !0 for piston rod for guide rod No. !1 !2 !3 !4 !5 !6 !7* !8* !
W 3 port normally open SOL.C 7.
Anodized Rod cover Aluminum alloy 1 1 PS NCA 500 2 Electroless nickel plating Cushion valve Rolled steel 2 3 Phosphate coated Snap ring Spring steel 2 Special options Nil XB5 XB6 XB7 XB5B6 XB5B7 Bore 500 600 800 4 Cushion valve seal NBR 2 Standard Oversized rod High temperature Low temperature Oversized W/ high temperature Oversized W/ low temperature Anodized Head cover Aluminum alloy 1
A full range of order made specifications -XA0 to XA30 -XB5 -XB6 -XB13 -XC3 -XC4 -XC5 -XC6 -XC7 -XC8 -XC9 -XC10 -XC11 -XC12 -XC18 -XC22 -XC30 -XC35 -X846 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Modification of rod end shape Heavy duty rod Heat resistant cylinder (to 150C) Low speed cylinder Special port locations With heavy duty scraper Heat resistant cylinder (to 110C) Stainless
Low speed cylinder (5 to 50mm/s) XB13 Accessories Special port position XC3 With heavy duty scraper XC4 Basic Foot Front flange Rear flange Single clevis Double clevis Center trunnion Heat resistant cylinder (110C) XC5 Mounting XC6 Piston rod and rod end nut made of stainless steel Rod end nut Tie rod, cushion valve, tie rod nut, etc.
(Or None in the Case of No Switch), X Option: XC6 (Piston Rod, Rod End Nut SUS)
(Or None in the Case of No Switch), Environmental Options: XC6 (Stainless Steel)