Modular Design with Uniform Body Style Install an air filter (AF series) as a pre-filter on the inlet side of the mist separator to prevent premature clogging. 2. Install a mist separator (AFM series) as a pre-filter on the inlet side of the micro mist separator to prevent premature clogging. 3.
back flow mechanism as a standard feature.
A manual operation mechanism is provided as standard equipment (non-locking).
A manual operation mechanism is provided as standard equipment (non-locking).
When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
-Pad ;;rol2 25 40 Flat type I a o o o a o a o o a o o Flat with rblo o a o o a a o eep tvpe lo a o a Bellows | a a a a a a o a a a 132 ZCDUKC Male Cap porting zPf (v&uum pad !
-Pad ;;rol2 25 40 Flat type I a o o o a o a o o a o o Flat with rblo o a o o a a o eep tvpe lo a o a Bellows | a a a a a a o a a a 132 I ZCDUKC Male Cap porting zPf (v&uum pad !
In order to further improve stopping accuracy, the time from the stop signal to the operation of the lock should be shortened as much as possible. To accomplish this, use a device such as a highly responsive electric control circuit or solenoid valve driven by direct current, and place the solenoid valve as close as possible to the cylinder.
15 54.5 24.5 80 24.5 (mm) Stroke adjustable range Retracting 5 15 25 35 30 15 35 35 35 A dimension (Retracted side mounting) Extending Model Shock absorber at retraction end MXS25-10 MXS25-20 MXS25-30 MXS25-40 MXS25-50 MXS25-75 MXS25-100 MXS25-125 MXS25-150 26 36 46 46 43 27 48 46 46 Stroke 100 to 150 A Shock absorber at extension end Max. 35 Shock absorber at retraction end Dimensions not
Option Note ZS-28-CA-4 Sensor connector For PF3A7H ZS-46-A1 Bracket A Tapping screw: Nominal size 3 x 8 L (2 pcs.) ZS-46-A2 Bracket B Tapping screw: Nominal size 3 x 8 L (2 pcs.)
Keep wiring as short as possible.
Type 46 Type S46 Single solenoid coil is located on same side as the A, B port.
backflow mechanism as a standard feature.
In order to further improve stopping accuracy, the time from the stop signal to the operation of the lock should be shortened as much as possible. To accomplish this, use a device such as a highly responsive electric control circuit or solenoid valve driven by direct current, and place the solenoid valve as close as possible to the cylinder. 4.
In order to further improve stopping accuracy, the time from the stop signal to the operation of the lock should be shortened as much as possible. To accomplish this, use a device such as a highly responsive electric control circuit or solenoid valve driven by direct current, and place the solenoid valve as close as possible to the cylinder. 4.
When the effective stroke of the shock absorber decreases as a result of stroke adjustment, the absorption capacity decreases dramatically.
The proper tightening torque for pipe fittings is as shown in the table. As a rule, they should be tightened 2 to 3 turns with a tool after first tightening by hand. Be careful not to cause damage by over-tightening. Caution 1. The product cannot be used as a stop valve, of which zero leakage is required. The specifications of the product allow a certain degree of leakage. 2.
Extend the dimensions of A, H. when using a single/double knuckle joint together with a rod end nut. (To extend dimensions A/H, refer to the table below, and specify the product as Made-to-order -XAO.) Pin and cotter pin are attached for double knuckle joint.