ML2B ML2B + CEU2 START Stop signal Stop position Piston speed Stopping accuracy 100 to 500 mm/s 0.5 mm Idle running distance Braking distance Stop distance 2. ML2B + PLC (Overrun) (Run) Piston speed (mm/s) 100 0.5 300 1.0 500 2.0 800 3.0 1000 4.0 Stopping accuracy (mm) The graph below shows the relation between piston speed and overrun.
400 500 1000 1500 100 200 300 400 500 1000 1500 Piston speed mm/s Piston speed mm/s Piston speed mm/s Select the load mass from within the range of limits shown in the graphs.
Operating Conditions Mounting Orientation Cylinder MY2H40G-500 Average operating speed a 300 mm/s Mounting orientation Wall mounting 1. Horizontal mounting 2. Wall mounting z y P. 8-13-5 Wb: MGGLB25-200 (4.35 kg) x y x z Wa: Connection plate t =10 (880 g) MY2H40G-500 3. Ceiling mounting P. 8-13-5 4.
1000 1500 Piston speed mm/s 100 200 300 400 500 1000 1500 Piston speed mm/s 100 200 300 400 500 1000 1500 Piston speed mm/s MY2C MY2 H/HT Maximum Load Mass Select the load mass from within the range of limits shown in the graphs.
Bore size Series MB Pressure 0.5 MPa Load factor 50% Stroke 500 mm Series CS1 Pressure 0.5 MPa Load factor 50% Cylinder stroke 1000 mm 50 63 80 100 125 140 160 180 200 250 300 Average speed (mm/s) Series 1000 1100 Perpendicular, upward actuation 900 Horizontal actuation 800 700 600 500 400 300 200 100 VK VQ7-8-FG-S-A03 VQ7-8-FG-S-RA03 VZ VF 0 1000 1100 VFR 900 800 700 600 500 400 300 200
P1 LED lever meter Sensor S1 S3 Red is on: Output OFF Green is on: Output ON S4 S2 + P2 Red 1 Gap too big S1, S2: Fixed orifice S3: Variable orifice (Set via adjustment knob) S4: Detection nozzle Red 2 Green 1 BEST POSITION The bridge circuit is constructed as shown in the diagram. Position the work piece in front of the nozzle (S4).
Mount switches in locations where there is no vibration greater than 98 m/s2, or impact greater than 490 m/s2. 3. Do not use in an area where surges are generated.
speed (mm/s) Collision speed (mm/s) L unit 1000 1000 Air cushion 500 400 300 500 400 300 L unit Air cushion 200 200 1002 3 4 5 10 20 50 100 1 2 3 4 5 10 20 30 400 50 Caution Load weight (kg) Load weight (kg) 1.
Wall mounting Cylinder MY1MW40-500 z Average operating speed a 200 mm/s Mounting orientation Horizontal mounting y Wd: Workpiece (500 g) x y Wc: MHL2-16D1(795 g) x z Wa: Connection plate t = 10 (880 g) x 3. Ceiling mounting 4. Vertical mounting MY1MW40-500 z y x y z Wb: MGGLB25-200 (4.35 kg) For actual examples of calculation for each orientation, refer to the pages above. 2.
(Error number 5) Vs : Power supply 24 VDC A : Input signal 4 to 20 mA DC 0 to 20 mA DC Vs : Power supply 24 VDC Vin : Input signal 0 to 5 VDC 0 to 10 VDC 4 points preset input type Brown Blue S1 White Vs Black S2 Vs: Power supply 24 VDC (Negative common) One of the preset pressures P1 through P4 is selected by the ON/OFF combination of S1 and S2.
Series SYJ3000/5000/7000 and Series SYJ300/500/700 can be mounted on the same manifold. How to mount on the same manifold is shown on the following pages. PDisconnection To remove the socket from the connector, pull out lead wire while depressing the hook of the socket with a fine screw driver (or similar). If the socket is to be re-used, reposition the hook again.
Note) AC-type models that are CE-compliant have DIN terminals only. 164 3 Port Valve 10-SY300/500 Note) CE-compliant: For DC only.
Tightening torque should be set 0.10 to 0.20 N.m. 11 Series C55 Auto Switch Specifications Auto Switch Common Specifications Reed switch Type Leakage current Solid state switch 3-wire: 100 A or less 2-wire: 0.8 mA or less None Operating time 1.2 ms 1 ms or less 300 m/s2 1000 m/s2 Impact resistance 50 M or more at 500 VDC Mega (between lead wire and case) Insulation resistance Withstand voltage
actuation 600 500 400 300 200 100 0 SX3140-01 900 800 700 600 500 400 300 200 100 0 SX5140-02 900 800 700 600 500 400 300 200 100 0 SX7140-03 It is when the cylinder is extending that is meter-out controlled by speed controller which is directly connected with cylinder, and its needle valve with being fully open.
Cylinder Speed Chart Bore size Series CJ2 Pressure 0.5 MPa Load factor 50% Stroke 60 mm Series CM2 Pressure 0.5 MPa Load factor 50% Stroke 300 mm Series MB Pressure 0.5 MPa Load factor 50% Stroke 500 mm 6 10 16 20 25 32 40 40 50 63 80 100 Series Average speed (mm/s) 800 700 600 500 400 300 200 100 0 It is when the cylinder is extending that is meter-out controlled by speed controller which
ZP3EA-S2 [Weight: 7.6 g] 24 47 15 29 4 20 36 Applicable pad part no. ZP3E-63UM ZP3E-80UM ZP3E-100UM ZP3E-125UM ZP3E-63BM ZP3E-80BM ZP3E-100BM ZP3E-125BM Applicable pad part no.
Hz at whichever is smaller of 1.5 mm amplitude or 98 m/s2 acceleration, in X, Y, Z directions, for 2 hours each (De-energized) 980 m/s2 in X, Y, Z directions, 3 times each (De-energized) Impact resistance Temperature characteristics (Based on 25C) 2% F .S. or less based on the analog output value at 25C from a range of 0 to 50C Port size M5 x 0.8 Material Body: Stainless steel Grade 303,
S1 S2 Effective area ratio 2.3 : 1 Pressure loss: Large K M 3 Without nozzle 3 H Pressure Loss of Air Gun Only Effective area (mm2) Upstream side S1: 15 Nozzle side S2: 6.4 D S1 : S2 = 2.3 : 1 Effective area ratio Nozzle size (mm) Number of nozzles Supply pressure Regulator pressure Outlet pressure Pressure loss 3 MS Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco,
Size: 63, Motor Type: S7 [AC Servo Motor (Absolute Encoder) 200W], Lead, mm: Size 40: 8mm, Size 63: 10mm, Stroke: 500mm, Motor Option: None, Cable Type: Standard, Cable Length: 2m, Driver Type: -, I/O Connector: -
Series: LEFS (Ball Screw Drive), Accuracy: Basic Type, Size: 32, Motor Mounting Position: In-line, Motor Type: S3 (200W Output, Incremental Encoder), Lead: A (LEFS25, 12mm; LEFS32, 16mm; LEFS40, 20mm), Stroke: 500mm, Motor Option: w/o Option, Auto Switch Mounting Bracket: None, Grease Application: with, Positioning Pin Hole: Housing B, Bottom, Cable Type: S (Standard Cable), Cable Length: