Rated Flow Range: 0.01 to 1 L/min, Flow Adjustment Valve: None (Straight), Port Size: NPT1/8, Output Specification: Out 1: PNP; Out 2: Analog 4 to 20 mA, Lead Wire: Lead Wire w/Connector + Rubber Cover for Connector, Unit Specification: Unit Selection Function, Bracket/Panel Mount Adapter: Bracket, w/o Flow Adjustment Valve, Calibration Certificate: -, Made to Order: -
VQC Use the following UL approved products for DC power supply combinations. (1) Controlled voltage current circuit conforming to UL508 Circuit uses the secondary coil of an isolated transformer as the power supply, satisfying the following conditions.
L8 L8 x n pcs. + L16 x 2 + L26 x (n1) pcs. L8 x n pcs. + L17 x 2 + L26 x (n1) pcs. L8 L8 x n pcs. + L25 x 2 + L26 x (n1) pcs. L27 + L8/2 Bonnet Mounting surface Refer to page 6 for L8. The figure above shows the manifold with speed controllers connected using two DIN rail mounting brackets, adapters and a threaded stud kit for manifold.
Description Material Note 1 Body Spool Sleeve Spool valve Piston Pilot valve Aluminum die cast / Metal seal Stainless steel 2 Rubber seal / Aluminum NBR 3 4 Resin 33 Series VQZ Body Ported Type Dimensions: VQZ100 Dimensions: VQZ100 (mm) Valve Scale: 65% Grommet (G): VQZ115G -N1, N3, N7, M5 2-N1, N3, N7, M5 N1: One-touch fittings for 1/8" N3: One-touch fittings for 5/32" N7: One-touch fittings
Supply pressure verification Leak test P2(n1) > P1(n2) P2(n2) P1(n1) 10.0 to 101.0kPa CH Increases the set value 1 2 3 4 PRESSURE For normally closed P2(n1) > P1(n2) P2(n2) P1(n1) 0.1 to 1000.0MPa Decreases the set value SET P3(n3) and P4(n4) are the same as P1(n1) and P2(n2).
The cushion effect (smooth start-up, soft stop) cannot be obtained in an intermediate stop or return from an intermediate stop using an external stopper, etc.
an input/output signal of ON/OFF counter function.
Note 1) Values indicated by an asterisk () are optional.
Note) Please contact SMC when using an individual EXH spacer assembly, an individual SUP spacer assembly, an adapter plate assembly, or an interface regulator on 41P and 43P types.
If the power should not come back on, please contact SMC for an inspection.
Switching of valve is based on an electric signal from the connector. The valve coil is kept in a de-energized state even when there is an electric signal from the connector.
Install an after-cooler, air dryer or water separator, etc. Air that contains excessive drainage can cause malfunction of valves and other pneumatic equipment. To prevent this, install an after-cooler, air dryer or water separator, etc. 3. Use the product within the range of specifications for fluid and ambient temperature.
Please contact SMC for a specification sheet when placing an order.
Please contact SMC for a specification sheet when placing an order.
When an offset load is expected, provide a suitable mechanism such as a floating joint. 2) Use clean air (atmospheric pressure dew point temperature 10C or less). Use of a series AM mist separator (filtration rating of 0.3 m or less), or series AM + AMD (filtration rating of 0.01 m or less) is recommended.
Note 2) An auto switch magnet is not attached. In cases where an auto switch magnet is attached, please add -M9// at the end of the part number. (Not available for high temperature models) Note 3) Auto switch and solenoid valve are not attached.
When an offset load is expected, provide a suitable mechanism such as a floating joint. 2) Use clean air (atmospheric pressure dew point temperature 10C or less). Use of a series AM mist separator (filtration rating of 0.3 m or less), or series AM + AMD (filtration rating of 0.01 m or less) is recommended.
If the power should not come back on, please contact SMC for an inspection.
For details about silencers, refer to the AN series in the Best Pneumatics No. 7.
If the power should not come back on, please contact P/A for an inspection.