KFx-OMV0011 Union nut tightening tool Fitting size Proper tightening torque [Nm] KFG201 2 to 3 KFG203 KFG204 KFG206 3 to 4 KFG207 KFG208 5 to 6 KFG209 KFG210 8 to 10 KFG211 KFG212 10 to 12 KFG213 KFG216 16 to 18 Piping Method Caution (1) Take a tube having no flaws on its periphery and cut it off at right angles. (Use SMC's tube cutter TK-1, 2, 3, 5 or 6 for cutting.
When cutting the tube, use tube cutters TK-1, 2 or 3. Do not use pinchers, nippers or scissors, etc.
TQ1230001-OM103-A 3. Specifications 3.1.
TQ1230001-OM101-D 3. Specifications 3.1.
B: Fluid N2 add Specifications: Note 3) add 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 URL http://www.smcworld.com Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. 2022 SMC Corporation All Rights Reserved
When cutting the tube, use tube cutters TK-1, 2 or 3. Do not cut the tube with pliers, nippers, scissors, etc. These tools result in a poor quality cut (e.g. flattening, rough edges, poor angle) and can result in a bad connection between the tube and the fitting, causing disconnection of the tube and air leakage.
Please do not tighten the needle forcibly. (3)Tighten threads with the proper tightening torque.
Nominal width across flats 3 M5, 10-32UNF 0.05 1/8 0.17 1/4 0.23 3/8 0.25 1/2 0.4 (2) See the table below for the maximum number of rotations of the indicator for each size of ASB-*H series.
Refer to the catalog on SMCs website (URL https://www.smcworld.com) Note 3) Use VHK2(2 port valve) for vacuum. JIS symbol 2 port valve 3 port valve 10 4. Construction (2) VHK2A(R) VHK3A(R) (9) (4) (1) (5) (3) (11) (10) (7) (8) (6) No.
Use SMCs tube cutter TK-1, 2 or 3 for cutting. Do not cut the tube with pliers, nippers, scissors, etc. If the tube is cut by any tools other than a tube cutter, the cut surface of the tube will be slanted or flat, making it impossible to be connected securely, or causing the tube to come off or air leakage after the tube is connected.
(Use tube cutter TK-1, 2 or 3. Do not cut the tube with cutting pliers, nippers, scissors, etc.) Flat or angled cuts will make it difficult to connect to fittings or, if connected, tube will release or air leakage will occur. 2. Grasp the tube, then slowly push it until it comes to a stop. 3. Pull it back gently to make sure that it has a positive seal.
Weight (g) A L 1 8 1 4 1 8 1 4 3 8 1 8 1 4 3 8 1 4 3 8 1 2 1 4 3 8 1 2 H04-01 15 4 10 H04-02 14 10 21.1 23.1 10 25.1 29.1 4 10 17 H06-01 11 12 21.1 25.1 6 H06-02 16 29.1 19 17 12 14 23.1 24.8 21.1 23.1 24.8 23.1 24.8 25.9 24.1 24.8 25.9 59 14 12 H06-03 31.1 31 H08-01 25.1 16 20 8 14 H08-02 16 29.1 21 17 14 H08-03 31.1 30 17 34 10 17 H10-02 29.1 28 H10-03 17 31.1 37 H10-04 34.1 53 H12-02 30.1
(Figure 2) 3. Tighten the silencer plate with round head combination screws. (Tightening torque: 0.12 +/0.01Nm) Fig. 2 Silencer ZQ-SAE Manifold type 1. Loosen the four hexagon socket head cap screws to remove the two silencer blocks. (Figure 3) 2. Replace the sound absorbing Fig. 3 material (ZZQ-SAE) in the silencer block. (Figure 4) Hexagon socket head cap screw 3.
TQ1230001-OM102-B 3. Specifications 3.1.
TQ1230001-OM104-C 3. Specifications 3.1.
Remove the excess sealant. (1) Connection and disconnection of tube from one-touch fitting (2) Insufficient tightening may loosen the Installation of tube 1) Cut the tube perpendicularly, being careful not threads, or cause air leakage. (3) Reuse Normally, fittings with a sealant can be to damage the external surface. Use an SMC tube cutter TK-1, 2, 3 or 6.
Use an SMC tube cutter TK-1, 2, 3, 5 or 6. Do not cut the tubing with pliers, nippers, scissors, etc., otherwise, the tubing will be deformed and trouble may result. matter may stick to the product or get mixed in the product's interior. This may cause leakage or disconnection of the tubing.
(Use SMC's tube cutter TK-1, 2, 3, 5 or 6 for cutting. Do not use pinchers, nippers or scissors, etc.) The tubing might be cut diagonally or flattened, making installation impossible or causing problems such as disconnection and leakage. 6 - 2. Specific Product Precautions (3) (5) Fix the body with a tightening tool.
Fitting size Proper tightening torque [Nm] KFG204 2 to 3 KFG206 3 to 4 KFG208 5 to 6 KFG210 8 to 10 KFG212 10 to 12 6 - 2. Specific Product Precautions (3) Warning (3) Ensure that the fluid and ambient temperature are within the specified range.
Use an SMC tube cutter TK-1, 2, 3 or 6. Do not cut the tubing with pliers, nippers, scissors, etc., otherwise the tubing will be deformed and problems may result. 2) The outside diameter of the polyurethane tubing swells when internal pressure is applied to it. Therefore, it may be impossible to reinsert the tubing into One-touch fittings.