Title not found Do you have a process requiring cost-efficient automation? Do you have a new series of safety features to implement? In fact, do you need another pair of hands in order to solve that troublesome domestic project?
If operating pressure is over the range then cylinder will be damaged and injury by broken pieces. (4) Do not put your hand into the slit of the body without confirming safety. Injury and Bodily harm will occur with the valve operated when valve is operated valve. (5) Do not remove the Cover Fig.1 29 on the actuating part.
Do not use the product in an environment where corrosive gases or fluids could be splashed. Otherwise damage to the product and malfunction can result. Do not use in an area where surges are generated.
Conditions Body ported Tube bore x Length Speed controller Silencer Series CJ2 Series CM2 6 x 1 m AS3301F-06 12 x 1 m AS4001F-12 AN200-02 Series MB 6 x 1 m AS2301F-06 AN110-01 VZ5120-01 3-3-55 Series VZ5000 Construction 2 position single 2 position double De-energized De-energized 3 position closed center/exhaust center/pressure center 3 position closed center De-energized De-energized 3
Do not disassemble the product or remove parts as it could cause breakdown of the product. 2. Flow rate is controlled by balancing the valve body. Do not expose the product to external vibration and impact as it changes the flow rate. Vibration may occur depending on the piping conditions or control methods.
Connect End Plate and tighten removed screws by specified tightening torque. (0.6 Nm) SW1 SW2 SW3 SW4 SW5 SW6 Node ID Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Socket connector pin layout 5 Green / Yellow: Not connected Specifications Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
ON BUS OUT side: Link, No Activity 1 2 3 4 5 6 7 8 (Green) Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do the same for release (push and rotate for 90 degrees). Tighten the piping using the correct torque shown below.
Warning Environment (1) Do not use in environment where the product is exposed to corrosive gas, chemicals, salt water, water or steam. (2) Do not operate the product in a location where it is subject to strong vibration and/or shock. For vibration, it should be within 1G 60Hz. ! ! ! ! -6- 7. Maintenance Warning (1) If handled improperly, compressed air can be dangerous.
Warning Environment (1) Do not use in environment where the product is exposed to corrosive gas, chemicals, salt water, water or steam. (2) Do not operate the product in a location where it is subject to strong vibration and/or shock. For vibration, it should be within 1G 60Hz. ! ! ! ! -6- 7. Maintenance Warning (1) If handled improperly, compressed air can be dangerous.
Do not use in locations having an explosive atmosphere. 2. When vibration or impact is applied, make sure to test in the 2.
Connect End Plate and tighten removed screws by specified tightening torque. (0.6 Nm) Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Note 1. The power supply should be off while setting the switches. 2.
Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not operate in locations where vibration or impact occurs. 3. In locations which receive direct sunlight, provide a protective cover, etc. 4. In locations near heat sources, block off any radiated heat. 5.
Do not operate in environments with corrosive gases, chemicals, sea water, fresh water or water vapor, or where there will be contact with the same. 2. In locations exposed to direct sunlight, block the sunlight. 3. Do not operate in locations where vibration or impact occurs. 4. Do not operate in a location near a heat source where radiated heat will be received. Pressure gauge 1.
Do not put the heavy objects on the products. Do not use the products as scaffold. 2. Do not use the products in conditions that do not meet the product specications. Product Returns When returning the product to SMC, make sure to properly purge to remove all hazardous materials and return the product complying with SMC specied procedures.
Do not use in atmospheres contacting corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not use in explosive atmosphere. 3. Do not use in locations subject to vibration or impact. 4. Do not expose to direct sunlight for an extended period of time. Protective cover should be used to shield. 5.
Do not operate at pressures or temperatures, etc., beyond the range of specifications, as this can cause damage or malfunction. We do not guarantee against any damage if the product is used outside of the specification range. 2.
Do not use the auto drain valve in such environment.
Burst pressure 25 20C to 60C Nylon 12 Min. bending radius (mm)(1) Operating temperature Material Note 1) The value at temp. of 20C and with O.D. variable rate 10% max.