NVZ1000//3000/5000 4,5 Port Solenoid Valve/Rubber Seal Type ft diagEm E : With indicator light and surco voltage suppssor i e l s I 3 14' 6 , ' , Lr 2.09 (s3) 2.72 (6e) 3.35 (85) 3.98 (101) 4.61 (117) 5.24 (i33) (i4e) 6.50 (165) (i&) (197) 8.39 (2|3) (?
'/s stl=0.44 300 (3") ]/s & 1/a st. 1/e &r/l st. 1/e & 1A st. 400 (4) 1/s &1/a st. r/s & 1/a st. 1/e &14 st. Series NCQT Dimensions Spring Extend NCQTBO-OT T Type Bore,, 9t4,F' I 60re ,b,:!
14 ' 140"F {-10-+60'C} 2 16 inlsec {50-400mn/s} Urethane cushion at both sides [lax. operating pressure Min. operating pressure Ambient and fluid temperature Operating piston speed Cushion Lubrication Stroke tolerance 0-9.gstlb6s, 10-39.4st: tbs, 39.sst-:13?
Do not use a tool when rotating the handle. When the handle is rotated with a tool, it may apply excessive torque to the handle or inside the valve body and it may cause damage. Rotate the handle by hand. 9. When locking the valve with LOTO feature in the closed position, use safety lockout hasp.
Thread type Port size Nil Rc N NPT 01 1/8 02 1/4 Related Equipment Check Valve INA-14-290/XTO-674Water Strainer Series WF300 Body material: Bronze Mesh: 100/70/50/25 mesh 14-E628 Body material: Brass Best Pneumatics Port size: Rc1/8 Port size: Rc1/4, 3/8, 1/2 WR110--X224/WR110--X215 14-E627 WR110--X224/WR110--X215 Flow Rate Characteristics Conditions/Fluid: Water, Port size: Rc1/4 WR110-02
To prevent this, do not set the supply pressure higher than necessary. Soft workpiece Workpiece that has concave/convex surfaces As soft workpieces are easy to deform, there is a tendency for the workpiece to touch the bottom of the non-contact gripper. Please be aware that the workpiece may touch the gripper before using.
When the element comes to the end of its life immediately replace it with a new filter or replacement element (cartridge type). 4 Do not disconnect and replace the one-touch fitting. Environment Warning Warning 1. Do not use the product in the following environments, which could cause failure. Seals the element, cover and fitting body. A place exposed to water, steam or oil.
Do not use solvents such as benzene, thinner etc. to clean the product including the switch cover. Use a soft cloth to remove stains. Refer to the SMC website (URL http://www.smcworld.com) for more information about troubleshooting. This operation manual refers to all standard types and is partially applicable to special models.
Do not use solvents such as benzene, thinner etc. to clean the product including the switch cover. Use a soft cloth to remove stains. Refer to the SMC website (URL http://www.smcworld.com) for more information about troubleshooting. This operation manual refers to all standard types and is partially applicable to special models.
Do not place your finger in the clearance between the detent plate and the cylinder tube. Never put your finger between the nonrotating plate and cylinder tube. Your finger may be pinched when the piston rod retracts. If your finger is caught, it could injure your finger because the cylinder outputs a considerable amount of force. 2.
H D DO 2 01 1 8 1 8 Base mounted 02 1 4 1 4 Caution Refer to front matters 58 and 59 for Safety Instructions and pages 3 to 7 for 3/4/5 Port Solenoid Valve Precautions.
: Without connector Manifold Model Applicable manifold type Accessories Function plate (DXT152-14-1A) Note) VO307(-Q) Common or individual exhaust Mounting screw (NXT013-3) Note) It is not applicable to the continuous duty type.
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed.
Do the drain pulling out regularly.
Do not subject the gauge to impacts, such as dropping, during transportation and mounting. This can cause loss of indication accuracy. 2. Do not use in locations with high temperature and humidity. This can cause malfunction. 3. When screwing the pressure gauge into place, be sure to apply your wrench on the square wrench flats.
Note 2) The output functions operate only for the real-time flow rate display, and do not operate for the accumulated flow display.
Specifications Air, Nitrogen Fluid 100 to 0kPa (-14.5 to 0psi) Operating pressure 0.5MPa (72.5psi) Withstand pressure 0 to 60C (32 to 140F) (with no freezing) Operating and ambient temperature range 10m Filtration degree Element differential pressure resistance 0.15MPa (21.75psi) Applicable tubing material Nylon, Soft nylon, Polyurethane, Soft polyurethane Symbol Note) Do not use in a line
Do not disassemble the power clamp cylinder. The power clamp cylinder consists of a completely sealed structure in order to protect it from welding spatter. Do not disassemble, except for when replacing any of the replaceable parts, as the performance may deteriorate. 10 Power Clamp Cylinder Variations Web Catalog.
Do not apply external force to the coil section. When tightening is performed, apply a wrench or other tool to the outside of the piping connection parts. Port Air operated Solenoid 12 (P1) External pilot External pilot 2. Do not warm the coil assembly with a heat insulator, etc. Use tape, heaters, etc., for freeze prevention on the piping and body only.
Caution D: With connector DO: Without connector Y: With connector YO: Without connector When using the surge voltage suppressor type, residual voltage will remain. For details, refer to the Web Catalog (VP300/500 Low wattage specification). * Refer to the Web Catalog (VP300/500 Low wattage specification) for details of the DIN terminal. Assembly Example Products do not come assembled.