IDX-OM-W019 Do not ground to water pipe, gas tube or lightening rod line. 7. Do not connect too many wires to the same outlet, which could results in heat generation and fire. 8. Do not retrofit the wiring of the dryer and the power supply line. 9.
Do not twist the valve seal 1.
Reset content Item Reset content PS1 0kPa PS2 0kPa *(Note): Gain (GL and sensitivity (SL) are not reset. 24 - Error indicating function Error LED display Contents of error Countermeasure name Please execute "initialize (refer to P33)" when ITV do not operate normally after restarting the power supply. Please contact us, when ITV do not operate normally after initialize.
Do not use the filter regulator where containing those. Effects organic solvents and chemicals, and where these elements are likely to adhere to the equipment.
Do not use the filter regulator where containing those. Effects organic solvents and chemicals, and where these elements are likely to adhere to the equipment.
Special tool F Special tool part number list Applicable bore size (mm) 6, 10, 15, 20 25, 32, 40 50 63 Part no. CYRZ-V CYRZ-W CYRZ-X CYRZ-Y 12REA Warning 1. Do not disassemble the product because it may damage the air cushion mechanism. Contact SMC when disassembly or maintenance is necessary . 169
Do not connect the earth to a water pipe, a gas pipe, or a lightening rod. Do not plug too many leads into a single socket. That causes exothermic heat or fire. Do not modify the internal electrical wiring of the product. 10.2 Specifications An earth leakage breaker is installed in the product.
bytes Output 36 bytes Input 36 bytes Output 36 bytes Input 36 bytes Output 36 bytes Input 4, 10, 20 bytes Output 4, 12, 20, 36 bytes Input 14 bytes Output 22 bytes Terminating resistor Not included Memory EEPROM LED indicator PWR, RUN, ALM, ERR PWR, ALM, MS, NS PWR, ALM, SF, BF PWR, ALM, MS, NS PWR, ALM, COM Cable length [m] Actuator cable: 20 or less Cooling system Natural air cooling Operating
(made by SMC) Operating ambient temp: -10 to +50 oC Storage ambient temp: -20 to +60 oC 1: Input terminal are not isolated from Power source. 2: Do not connect outside Power source to Input and Output terminals. 62 63 0 1 1 1 1 1 1 1 1 1 1 1 Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result.
Do the same for release (push and rotate for 90 degrees). Tighten the piping using the correct torque shown below. Use an External pilot pressure higher than IN port pressure. Table.2 Thread Appropriate tightening torque (Nm) 1/2 20 to 25 -8 - 6.
Do not apply excessive force or impact. This will not only damage the product but also decrease its performance and life expectancy. It is not possible to disassemble the bonnet assembly of this product. If the components and assembly are damaged, or damage is expected, exchange the bonnet assembly itself. Do not disassemble the parts that are not explained in this operation manual.
(made by SMC) Operating ambient temp.: +5 to +45 oC Storage ambient temp.: -20 to +60 oC 1: Input terminal are not isolated from Power source. 2: Do not connect outside Power source to Input and Output terminals. Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof.
(made by SMC) Operating ambient temp: +5 to +45 oC Storage ambient temp: -20 to +60 oC 1: Input terminal are not isolated from Power source. 2: Do not connect outside Power source to Input and Output terminals. ) ( Assignment of I/O No.
Do not use this product outside of the specifications.
Regarding products for general fluids, please contact SMC concerning applicable fluids. (3) Do not use in a place subject to heavy vibration and/or shock. (4) Do not mount the product in locations where it is exposed to radiant heat. (2) When there is a large amount of drainage. (5) Do not use the ordinary fittings and tubing Compressed air that contains a large amount of drainage can cause
Description XLS-16XLS-16-P XLS-25XLS-25-P (2) Coil assembly XLS16-20-*G,C,D,T XLS16-20-P*G XLS25-20-*G,C,D,T XLS25-20-P*G (6) Core assembly XLS16-30-1 XLS25-30-1 (4) Armature assembly XLS16-30-2 XLS25-30-2 (3-1) Core O-ring AS568-018V AS568-018V (3-2) Bonnet O-ring AS568-025V AS568-030V Note) Enter voltage no. at * G, C, D, and T after * mean the symbol showing an electrical entry. 6 XL
Do not use in lines where a pressurized condition is maintained, as the body may be damaged. Warning Caution 1. Tubing attachment/detachment for One-touch fittings 1) Installing the tubing (1) Use tubing with no flaws on its periphery and cut it off at a right angle. When cutting the tubing, use a tube cutter, TK-1, 2 or 3. Do not use pinchers, nippers or scissors, etc.
40 60 80 100 120 140 0 10 20 30 40 50 60 70 80 90 100 Flow rate L/min (ANR) Flow rate L/min (ANR) SRP1101-01 Conditions/Inlet pressure: 0.5 MPa SRP1-01 Conditions/Inlet pressure: 0.7 MPa 0.25 0.50 0.20 0.40 Outlet pressure MPa Outlet pressure MPa 0.15 0.30 0.10 0.20 0.05 0.10 0.00 0.00 0 20 40 60 80 100 120 140 160 180 200 0 20 40 60 80 100 120 140 Flow rate L/min (ANR) Flow rate L/min (
Do not connect multiple NFC readers / writers to a PC. Connection details using the I/O Configurator for NFC and wireless unit To use a wireless system, it is necessary to "pair" a Wireless Base and Remote. Configure this using the I/O Configurator (NFC version).
Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.