EX600-LAB1_LBB1.eng

Red ON Short circuit at L+ or C/Q LED 1, 2, 3, 4 for I/Q (EX600-LAB1) Function LED status Description End plate bracket (EX600-ZMA2) OFF Input OFF I/Q Orange ON Input ON CAUTION indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury.

High Purity Fluoropolymer

J type fitting assembly procedure J type Pull out the lever pin q. Rotate the lever assembly w to align the holes on the lever assembly w and the base e. Insert the lever pin q into the holes to fix the lever assembly w. 1 y Tubing !

Digital Flow Switch For Air/Water Series PF2A/PF2W

The display of the accumulated flow will be reset to zero. q r q w LCD display/Orange Displays the measured flow rate, each setting condition, and error code. e Output (OUT1) display/Orange Displays the output condition of OUT1. Illuminates when turned ON. i Displays the selected unit.

High Purity Fluoropolymer Fittings HYPER FITTING ® Series LQ1 1

J type J type fitting assembly procedure Pull out the lever pin q. Rotate the lever assembly w to align the holes on the lever assembly w and the base e. Insert the lever pin q into the holes to fix the lever assembly w. 1 !

VXD21/22/23

59 59 60 P Port size Rc VXD2140 Q R a b c d e f M L K J H F E D C B A N 69 (76) 77 (84) 87 (97) Q N 61 69 79 Q N 61 (68) 69 (76) 79 (89) N 61 (68) 69 (76) 79 (89) Normally open Normally closed VXD2142 , 30 30 35 59 59 62 57 74 81 34 51 58 29 37 43 34 43 47 20 20 23 92 92 95 104 (116) 26 44 59 66 28 35 40 3 8 8 14 23 39 47 47 48 39 65 78 86 42 46 56 52 56 66 63 80 90 3 8 1 2 32.5 118 (136)

Large Size 3 Port Solenoid Valve VP3145/3165/3185 Series Rubber Seal

Disassembly 1) After loosening the screw q, then if the housing r is pulled in the direction of the screw, the connector will be removed from the body of equipment (solenoid, etc.). 2) Pull out the screw q, then remove the gasket or . 3) On the bottom part of the terminal block e, theres a cut-off part (indication of an arrow) .

Vacuum Pad with Ejector ZHP Series Pad Diameter: ø63, ø80 ZK2 ZQ Ejector and pad are integrated. ZR Space saving and reduced piping labor! Bellows type with groove ZB ZA Two-stage ejector ZX More efficient ejector 30% reduced 50% increased ZM Air Suction

(Refer to q shown in the figure below.) If the lock plate is not locked completely, the pad may drop due to the vibration or load during operation. q ZA Holder y ZX Non-rotating hole Plate ZM 3. To ensure the safety, be sure to mount the lock screw on the lock plate before use. (Refer to w shown in the figure below.)

Desktop Duster Box

Nozzle 494 RoHS Desktop Duster Box ZVB Series IZS How to Order IZN A S B ZVB 20 IZF ZVB ZVB q w e r t IZD IZE Nil None Note 1) S With photoelectric sensor Note 2) r AC adapter q Size w Additional air blow B With additional air blow e Photoelectric sensor Note 1) It is necessary to connect an external switch to the external input terminal on the back side of the product.

0.5

Red flashes if the CPU is abnormal. q w e r t y u Green lights up when emitters require cleaning.

Suction Guard (Produced upon receipt of order) FHG Series

Port size q Seal order no. r Seal order no. t Seal order no.

Vacuum Filter AFJ Series

q r r w w (y) e (y) t e t Component Parts No.

Direct Operated Precision Regulator Series ARP20/30/40  Sensitivity: Within 0.2% F.S.  Expanded lineup  ARJ 3 types of set pressure and the body size AR425  Energy saving, Air consumption: allow more freedom in designing a circuit. to 935 80% reduct

When the inlet pressure is shut off and released, the check valve w opens and the pressure in the diaphragm chamber q is released to the inlet side (Figure 2). This lowers the pressure in the diaphragm chamber q and the force generated by the pressure regulator spring e pushes down the diaphragm.

Direct Operated Precision Regulator ARP20/30/40 Series  Sensitivity: Within 0.2% F.S.  Expanded lineup  ARJ 3 types of set pressure and the body size AR425  Energy saving, Air consumption: allow more freedom in designing a circuit. to 935 80% reduct

When the inlet pressure is shut off and released, the check valve w opens and the pressure in the diaphragm chamber q is released to the inlet side (Figure 2). This lowers the pressure in the diaphragm chamber q and the force generated by the pressure regulator spring e pushes down the diaphragm.

air-filter-e

KT-FGDC KT-FGDE KT-FGDT KT-FGDF Replacement parts A 1 kit for each of each one of seals q to t and gasket.

Cylinder with Lock

Refer to page 41 for how to return to the locked state. 10 MWB Series Construction io w er uy q !3 !4 !2 !8!5!6 !0!1 !7 @1@0 @2 @6 @3 @5@8 @4@9 #5 #7 #9 #8#6#4 #0#1 $1 $0 t !9 #3 #2 @7 Component Parts Component Parts No. Description Material Qty.

Mist Separator Series AM Model Series AM can separate and Model AM850 AM250 AM350 AM450 AM550 AM650 AM150 remove oil mist in compressed air Rated flow 750 1500 2200 3500 6000 12000 300 (1) (l/min (ANR)) which is difficult to remove by Port size ordin

AMl Related poroducts Maintenance Caution q The replacement interval for the element is when the pressure drop reaches 0.1MPa or after 2 years of operation, whichever comes first.

Micro Mist Separator Series AMD Model Series AMD can separate and Model AMD450 AMD550 AMD650 AMD850 AMD150 AMD250 AMD350 remove aerosol state oil mist in Rated flow (l/min (ANR))(1) 2000 3500 6000 12000 200 500 1000 compressed air and remove Port size

Chrome treatment (Epoxy coating on inner surface) Housing Body q w e Tempered glass Sight glass AMD850 is aluminum casting Replacement Parts AMD450 Part No. Description Material No.

AME

AFF AMl Related poroducts Mounting Caution q Verify the direction of the flow of the compressed air and the e mark that indicates the inlet of the product before connecting.

AMF

ORIENTATION Caution on Design Caution q Design the layout so that the mist separator is installed in an area that is less susceptible to pulsations.

Air Preparation Equipment

KT-FGDC KT-FGDE KT-FGDT KT-FGDF Replacement parts A 1 kit for each of each one of seals q to t and gasket.