Series KP/KPQ/KPG Block off the heat with a cover, etc. 5. Do not use in locations where static electric charges will be a problem. Consult SMC regarding use in this kind of environment. 6. Do not use in locations where spatter occurs. There is a danger of spatter causing a fire.
VN LVC LVA LVH Variations LVD LVQ Valve Material Base, Body Seal Aluminum NBR, FKM, EPDM LQ Common SUP Individual SUP Common SUP Individual SUP Port A Port A Normally closed (N. C.) LVN Port P TI/ TIL Port P Port P PA Port A PAX Port A Port A PB Normally open (N. O.)
Block off the heat with a cover, etc. 5. Do not use in locations where static electric charges will be a problem. Consult SMC regarding use in this kind of environment. 6. Do not use in locations where spatter occurs. There is a danger of spatter causing a fire.
9200-www.stevenengineering.com When tightening an auto switch mounting screw, use a watchmakers screwdriver with a grip diameter of 5 to 6 mm.
(A value under a specified condition.) VX t Vaccuum pressure (Torr) The absolute pressure is expressed. 0 Torr=Absolute pressure 0.760 Torr=Atmospheric pressure (Gauge pressure 0 Kgf/cm2) (1 torr=1.33 X 102 Pa) VNl VQ Electrical Terms q Volt-ampere(VA) Volt-ampere is the product of voltage (V) and current (A). Power dissipation (W): For AC , W=V/A cos.
Temperature Data A or B = Series IDUS: Data A Series IDFS: Data B Air pressure Data C = 2 Calculate corrected air flow by using A or B and C. Corrected air flow = (Air flow) (Data A x Data C) Corrected air flow = (Air flow) (Data B x Data C) 3 Select a model having an air flow capacity that is higher than the corrected air flow.
lubricant that has a shielding effect from ozone.
Using a regulator in the outlet side When mounting a regulator in the outlet side (A port side), use a residual pressure relief regulator (AR25K to 40K) or a check type regulator. With a standard regulator (AR10 to 60), the outlet side pressure may not be released when this valve is exhausted. 5.
Install a suitable circuit breaker applicable to each model. Use a circuit breaker having a sensitivity current of 30mA or less and a rated current of 5A.
Temperature When operating at high temperatures (40C to 80C), there is danger of burns. Confirm that the surface temperature of the filter or the parts for operation are 40C or less, to prevent a burn from occurring. 531
If the drain bowl is difficult to check and remove, it is recommended that a drain bowl with the auto-drain option be installed.
Cooling water (l/min) 180C Inlet air temperature Correction factor Air flow (l/min (ANR)) Model 50C 70C 100C 41.5 43 45.5 37 43 49.5 37 43 45.5 37 42 43.5 40 44 46 39.5 43 44.5 41 43 45.5 A B C A B C A B C A B C A B C A B C A B C 35.5 36 36.5 33.5 36 38 33.5 36 36.5 33.5 35 36 34.5 36 37 34.5 35.5 36 34.5 35.5 36 38.5 40 42 36 40 45.5 36 40 42.5 36 40 41 38 40 42.5 38
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
Model A B C A B C A B C A B C 500 1000 1500 1000 2200 3000 2000 3300 4000 4000 5700 7000 34.5 38 40 33 36.5 38 34 36 37 34 35 36 35 40 44 35.5 40 42 37 40 41.5 38 40 42 35.5 42.5 47.5 36 42.5 44 38.5 42.5 45 39 43 45 HAA7 HAA15 HAA22 Maintenance HAA37 Caution 1. Inspect the cooler at least once a week and clean it to prevent it from becoming obstructed. 2.
Connect a drain pipe because a large amount of drainage is created when the compressed air is cooled.
Able to control a wide variety of fluids. ! VC VDW Easy to disassemble and reassemble in a shorttime. VQ High viscosity fluids (500 cSt).
When tightening the air inlet and outlet piping, make sure to use a pipe wrench to hold the inlet and outlet nozzles of the product. 2. Connect a drain pipe because drainage is created when the compressed air is cooled. 3.
Note 2) FluorinertTM is a trademark of 3M and GALDEN is a registered trademark of Solvay Solexis, Inc. Regarding the fluid other than the above, please contact SMC. Note 3) (1) Facility water temperature: 25C, (2) Circulating fluid flow rate: Values at circulating fluid rated flow rate. Values common for 50/60 Hz. Note 4) Thermo-cooler specifications do not have heating capability.